Is there a Hitch-Mounted Winch Mounting Plate for a Warn 8274 Winch

Question

Question:

receiver hitch mounting tray for Warn 8274 Which hitch winch mount will work?

asked by: Edward M

1

Helpful Expert Reply:

The Bulldog winch mounting plate # BDW20011 will work with most major winch brands. The same goes for Curt mounting plate # C31010. Even if a winch is not listed on the page that doesn't mean it won't fit which is why the hole spacing measurements are important. I have attached video of each for you to check out.

expert reply by: Michael H

1

Answer 1

I would be happy to help. On the bottom of the hitch ball will be a plastic or aluminum plug. Remove the plug and you will see a bar inside that is used to hold the bearings in place. You will need to rotate the bar 90 degrees to release the…

view full answer...

Answer 2

This Curt Trailer Hitch Winch Mount, part #C31010 has a capacity of 9,000 pounds straight pull. You will need to find the weight capacity of the hitch as well, and compare the capacities, using the lowest limiting factor. We do not sell Warn winches,…

view full answer...

Answer 3

I went out to the warehouse and pulled a CURT Trailer Hitch Electric Winch Mount Plate, #C31010, to measure it. From the back of the mounting plate to the center of the nearest hitch pin hole, it is 4-1/4 inches. -The distance to the center hole is…

view full answer...

Answer 4

The Curt Trailer Hitch Electric Winch Mount Plate #C31010 is not rated for line pull. That rating would be specific to your trailer hitch. Front mounted hitches are often rated in this way but rear mounted hitches are not. I would need to know your…

view full answer...

Answer 5

First, on the Curt trailer hitch mount winch mounting plate, the center to center distance between the fairlead mounting holes is 10-1/2 inches. In order to determine if your winch will fit the plate, you will have to compare the mounting hole…

view full answer...

Answer 6

From what I was able to find, the Warn M12000 winch is 24.37" L. x 8.45" D. x 11" H. I've attached a picture with the dimensions on the Bulldog Winch Hitch Mounted Winch Plate #BDW20011 but since the mounting cradle is only…

view full answer...

Answer 7

I checked with my contact at Bulldog and they said that the capacity of the Bulldog Winch Hitch Mounted Winch Mounting Plate #BDW20011, is based on capacity of vehicle receiver. This mount is made for winches up to 12.5 k and does not fit large-body…

view full answer...

Answer 8

You will need to check the bolt hole mounting pattern of your Badlands Winch, but we do offer several hitch mounted winch mounting plates that may work. First we have the Curt Mounting Plate, #C31010. On it, the first set of mounting holes are 10 by…

view full answer...

Answer 9

There really isn't a specific width (or thickness) of a winch mounting plate to use with a 12,000 lb winch. You just want to choose one that has a mounting bolt hole pattern that is compatible with your winch. The Bulldog Winch Hitch Mounted…

view full answer...

Answer 10

I checked with Curt and they do show the Curt Trailer Hitch Receiver part #C13233 as a fit for a 2022 Volvo XC90 All Models which includes the Recharge.

view full answer...

Answer 11

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 12

Since the issue appears to be on the vehicle side for your 2017 Toyota Tacoma, I recommend first checking the connector itself. Look to see if there is any dirt or corrosion built up inside the connector that may preventing a solid connection with…

view full answer...

Is there a Hitch-Mounted Winch Mounting Plate for a Warn 8274 Winch

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching