Replacement Key Recommendation for etrailer.com Coupler Lock

Question

Question:

Can I get a duplicate key for the blockhead walk?

asked by: Bryant S

0

Expert Reply:

We do offer a way to get replacement keys for your etrailer.com Coupler Lock # e98895.

Look on the lock and determine the key number. The key number will be 3 digits and it usually starts with a zero.

Once you have the find the key number you will type "Replacement key ___" into the etrailer search bar.

For instance if you type: Replacement key 029 into the search bar, the part # e75UR for key 029 will show.

You can also just ask again when you know the part number and we would be happy to help.

expert reply by: Jameson C

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 7

I took some measurements off the etrailer Trailer Coupler Lock #e98895 that will help you to determine if this will fit your coupler. The maximum width of the coupler tongue channel is 4-1/2" wide, and 2-3/4" deep. The locking pin is…

view full answer...

Answer 8

The LED Trailer Mini Clearance and Side Marker Light with Grommet #MCL10AKB will fit best with a wall (or bracket) thickness that is just under 5/16".

view full answer...

Answer 9

Since your 2008 Ford E-350 has a factory 7-way all you would need to install a brake controller like the Redarc Tow Pro Liberty part #RED24FR is the install harness part #RED87FR. I also really like the Redarc controllers for the reason you mentioned…

view full answer...

Answer 10

Yes, all you'll need to do is disconnect the three wires running from the converter section in your Progressive Dynamics 4100 #PD4135K from the AC distribution panel (circuit breaker, ground bus bar, neutral bus bar). This will cut the power…

view full answer...

Answer 11

The closest radial tire size I would have to replace the 4.80-12 bias tire size is the Kenda Karrier S-Trail ST145R12 Radial Trailer Tire #AM10130. The 4.80-12 bias tire is 20.7 inches tall and 4.9 inches wide. The 145R12 radial tire is 21.3 inches…

view full answer...

Answer 12

While the Rack'Em Fitz-All Enclosed Trailer Ladder Rack #RA-28 was designed to fit on trailer with a rain gutter, we have had several install it on their trailer without rain gutters. I have also included our review video below where you can see…

view full answer...

Replacement Key Recommendation for etrailer.com Coupler Lock

Product Page this Question was Asked From

Continue Researching