Replacement 30 Amp In-Line Circuit Breaker - Perpendicular Mount Bracket

Question

Question:

Is the body stamped with W29? I need a replacement and thats what my old one was marked with.

asked by: Johnny

0

Expert Reply:

The 30 amp circuit breaker # 38630 is an exact match for your current circuit breaker though it may not have W29 stamped on it. I spoke with Pollak about that designation and is a date code or batch number so you could get one that is completely different from W29.

expert reply by: Michael H

0

click to enlarge

Answer 1

On a circuit breaker like #9510 from Pollak the copper-color terminal will connect to the vehicle battery's positive post. The silver-color terminal connects to your 7-way's contact for the trailer charging circuit as shown in the linked…

view full answer...

Answer 2

Generally a circuit breaker should be installed close to the power source. On a trailer with on-board battery power breakers are best installed near the batteries and each circuit should have a breaker of the appropriate amperage value for the device…

view full answer...

Answer 3

LED lights draw considerably less amperage than incandescent lights. They also run much cooler. These 2 features are why LED lights last so long. The incandescent version of #STL8RB is #ST8RB and it draws 2.5 amps for the stop/turn signal functions…

view full answer...

Answer 4

The Tekonsha BRAKE-EVN Trailer Brake Controller - 1 to 4 Axles - Proportional #TK63VR should have the gain set at 8 or 9 since your trailer is so large compared to the truck. I'd start there and adjust up if you need more braking for comfort.…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 8

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 12

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Replacement 30 Amp In-Line Circuit Breaker - Perpendicular Mount Bracket

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching