Would it Be Better to Replace Straps of K Source Towing Mirror or Replace Entire Mirror

Question

Question:

does the straps come complete

asked by: Gary T

0

Expert Reply:

For replacement straps for the K-Source Towing Mirror part # KS3891 you would want the part # KS3891STR that you referenced. This comes with everything needed to replace both straps.

However, for the price it might be a better idea just to replace the entire mirror. It's just a few dollars more and you get everything new.

expert reply by: Jameson C

0

Answer 1

I was able to pull up your previous order and confirm your mirrors are the K-Source Universal Towing Mirror - Clip On #KS3891. The replacement straps you need are the Replacement Ratcheting Strap for K-Source Universal Towing Mirror - Clip On…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

According to my research, AL-KO 8490 references an AL-KO hub for 3,500 lb axles with a 10 x 2-1/4" drum and a 5 on 4-1/2" bolt pattern. For a drum assembly that will work with these hubs I recommend taking a look at the Electric Trailer…

view full answer...

Answer 5

The Dexter brake assembly 023-217-00 is a 10 by 2-1/4 brake for 3,500 pound axles that fits a 4-bolt brake mounting flange. For replacements I recommend part #AKEBRK-35-SA that includes both sides. They're labeld to make the install easier and…

view full answer...

Answer 6

Hi Rene; I'm sure it's frustrating to have the mirror fall off, and while there are only universal towing mirrors for your 2016 Nissan Frontier, there are better ones than the clamp-on (which I also do not like). I would definitely go with…

view full answer...

Answer 7

Dexter part 10-41 is a grease seal for a mobile home utility hub. It has a specified inside diameter of 1.938-inches and an outside diameter of 2.523-inches. The nearest match we offer is the Redline part #10-40 which is a single-lip seal that has…

view full answer...

Answer 8

The grease cap part number that you referenced cross references to a drive in cap with a 2.44 inch outside diameter. If you have a standard cap then the Grease Cap, 2.44 inch OD Drive In, item #RG04-060, is the correct part. If you have a grease…

view full answer...

Answer 9

There are 4 wires coming out of the back of the Draw-Tite Activator IV Brake Controller part 5504. You are correct in that the black wire runs to the positive side of the vehicle battery through a circuit breaker. The white wire runs to the negative…

view full answer...

Answer 10

Not confusing at all. I took a look online and the 2001 Silverado 2500HD has a 12,000 lbs bumper pull towing capacity and a 15,200 lbs 5th wheel towing capacity. It's just two different capabilities of the truck. The extra weight of a 5th wheel…

view full answer...

Answer 11

The dimensions you have are nearly identical to the CE Smith #CE19504-2 you looked at. However, these are designed for 14" wheels. For 15" wheels you would need the Fulton #F008585-2. These are slightly longer and taller at 10-1/4"…

view full answer...

Answer 12

I was able to get a dimension sheet from my contact at Curt for the Curt Hitch part #C15800 that you referenced. See attached pic. I also attached a set of the installation instructions for this hitch.

view full answer...

Would it Be Better to Replace Straps of K Source Towing Mirror or Replace Entire Mirror

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching