Availability of LED Version of Optronics Clearance Light # MC44RB

Question

Question:

One of the red clearance lights on my RV is out. Need replacement. Looks similar to Optronics MC44RB except mine is LED. It is rectangular about 4inch long, little over 1inch high. Mounting holes on 3inch center. Light is from 6 LEDs on a pc board. I have a photo, but will need your e-mail address to attach it.

asked by: John S

0

Expert Reply:

For an LED version of the part # MC44RB we have the part # MCL44RB1 which matches the dimensions you referenced.

expert reply by: Jameson C

0

Answer 1

To replace your GloBrite 126 marker lights you can use the #MC44RB. These lights are 2-wire incandescent lights measuring 4" long by 1-1/2" wide (same as your existing marker lights) and will work great for your trailer.

view full answer...

Answer 2

To replace your GloBrite 126 marker lights you can use the #MC44RB for the red light and the #MC44AB for the amber light. Both of these lights are 2 wire lights and will work well on your cargo trailer. And yes, we can ship this particular product to…

view full answer...

Answer 3

The correct replacement trailer clearance light for a Bargman 99 Series is the Optronics Trailer Clearance or Side Marker Light part #MC44RB for red or part #MC44AB or amber. The mounting holes for this light are spaced 3" apart on center. It…

view full answer...

Answer 4

I recommend using the Optronics Trailer Clearance or Side Marker Light w/ Reflex Reflector - Incandescent - Red Lens #MC44RB, which has mounting holes 3" apart like your existing lights and will be 4" long x 1-1/2" wide. These are an…

view full answer...

Answer 5

Torque specs for wheel lug nuts will vary depending on the diameter of the lugs, type of lug nut and the wheel's material. The linked chart details the recommended torque for many combinations. Dexter Hub/Drum #84546UC3 has 1/2-inch studs and…

view full answer...

Answer 6

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 9

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to stress…

view full answer...

Answer 10

According to my contact at Fantastic Vent the correct replacement lift motor to use in your vent is part #FVK6010-81, not item FVK-6050-80. The replacement motor does operate at a higher 17-RPM speed. Since your fan is of a lower rpm and manufactured…

view full answer...

Answer 11

The great thing about Bearing Buddy like part #BB1781 is that when you add grease to your system with the included fitting, it will move the spring-loaded piston outward and allow grease to seep around the edges to keep from damaging the seal. You…

view full answer...

Answer 12

The crank handle for the Lippert Components Spare Tire Winch with Offset Cable item #LC159056, is Replacement Crank Extension for Lippert Spare Tire Winch Assemblies - 35-1/2" item #LC1315411. The Spare Tire Winch item #LC159056 has a 1/2-inch…

view full answer...