Can the "Junior" Locking Stainless Steel Flush Door Latch be Locked/Unlocked from the Inside

Question

Question:

If you are inside the trailer can you lock or unlock the handle?

asked by: AARON L

0

Expert Reply:

No, if you are inside the trailer you cannot lock or unlock handle # L1833 but you can open the latch. The lock can only be operated using the key and the key hole is only on the outside of the trailer.

expert reply by: Michael H

0

Answer 1

The position of the Junior Locking Flush Door Latch, #L1833, will depend on the type of door you are installing it on. If the edge of the door on the trailer is going to be flush with the inside of the of the door jamb on the trailer, then this door…

view full answer...

Answer 2

Typically, the Junior Door Latch would install by routing or cutting out a 2-3/4 by 3-3/4 inch hole and would then either be bolted or riveted to the door through holes that would need to be drilled in the flange around the latch. The latch is meant…

view full answer...

Answer 3

The Dexter Single Axle Heavy Duty Suspension Kit part #K71-403-00 does not come with bushings. These will be required but they should already be installed in the leaf springs and equalizers. If yours need replaced you can use the Suspension Bushing…

view full answer...

Answer 4

The Dexter Single Axle Heavy Duty Suspension Kit #K71-403-00 uses the Shackle Bolt #007-126-01. The 9/16" portion of this bolt is 2-1/4" long.

view full answer...

Answer 5

The threaded portion of the bolts of the #K71-403-00 are 7/16 inch but the stepped up diameter is 9/16 inch. The shackle length is 3-1/8 inch from hole center to hole center. The bolt length is 2-7/8 inches. We can't help much with the axle…

view full answer...

Answer 6

The shackle links of the #K71-403-00 are 3/8 inch thick.

view full answer...

Answer 7

The Dexter Single Axle Heavy Duty Suspension Kit #K71-403-00 technically will not have a torque specification. However, I have been asked this before and was informed by Dexter that what you need to do is tighten them down to the point of either…

view full answer...

Answer 8

We can get you the right shackle kit for your single axle trailer with a Dexter 3,500 lb axle, and you can choose from either a standard kit or an upgrade kit. Either will work, though the Upgrade Kit is going to be the best option due to the fact it…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...