Thread Size of the Lippert Components JT's Strong Arm Jack Stabilizer Replacement T-Bolts

Question

Question:

I need a t handle bolt and see Lippert Components Accessories and Parts - LC314594. I need a 3/8 course thread bolt. Is that what this is?

asked by: T B

0

Expert Reply:

Yes, I went out and checked a Lippert Components JT's Strong Arm Jack Stabilizer Replacement T-Bolts # LC314594 we had in stock and the threads are 3/8 inch coarse.

expert reply by: Jameson C

0

Answer 1

For the JT's Strongarm kits we do have replacement handles with the part #LC314594.

view full answer...

Answer 2

Sounds like you are looking for replacement T-handles for your JT's Strongarm stabilizers like with the part #LC314594.

view full answer...

Answer 3

The Replacement T-Handles for JT's Strong Arm Jack Stabilizer Kits - Qty 2 #LC314594. The outer sleeve you are seeking is Replacement Outer Stabilizer for JT's Strong Arm Jack Stabilizer - 1-1/4" OD - Qty 1 #LC191014.

view full answer...

Answer 4

We do have the T-bolts, #LC314594, and I believe you also need the shorter swing bolts, #LC314595. But I checked with Lippert and the actual Strong Arms are only available in the kits. For trailers over 58 inches between the landing gear you would…

view full answer...

Answer 5

For the JT's Strong Arm Jack Stabilizer Kit #LC191024 the Replacement Outer Stabilizer #LC191014 will be the one you are looking for. The T-Handles #LC314594 are sold as a 2 pack. We also have the Replacement Swing Bolt Kit #LC314595 if that…

view full answer...

Answer 6

The red blinking light on the Atwood RV Carbon Monoxide and Propane Gas Detector part #AT36681 under the propane heading means that the propane sensor is disabled or faulty. I recommend doing a hard reset of the unit but if that does not work then…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 9

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 10

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 11

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 12

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Thread Size of the Lippert Components JT's Strong Arm Jack Stabilizer Replacement T-Bolts

Product Page this Question was Asked From

Continue Researching