What is Preferred Method For Securing Truck Tool Box to Truck Bed if J-Hooks Don't Work

Question

Question:

I have a UWS box on my Tacoma that has come loose from the original J Bolt mounts. The box is able to slide forward and back, along with side to side. What is the best way to secure the box to the bed again?

asked by: Grant

0

Expert Reply:

Best way is to drill a hole through the floor of the tool box and then through the bed of the truck and then run a bolt through both. This is the best way to secure a tool box.

expert reply by: Jameson C

0

Answer 1

The UWS Replacement Locking Paddle, part #UWSLOCKING would use a 3/16 diameter pop rivet.

view full answer...

Answer 2

The lift cylinders for the UWS toolboxes will lift the lid of a UWS toolbox, but you will need to assist the lift cylinder by lifting the toolbox lid a few inches before the lift cylinder opens the lid the rest of the way. It will not immediately…

view full answer...

Answer 3

The #UWSSTACHONS uses 7/8 inch diameter tubing or pipe which isn't included. The length of pipe would depend on what you decided to use.

view full answer...

Answer 4

Hey John, so the correct amount of spring bar tension will be based on the trailer's tongue weight and how it affects the suspension of your Nissan Frontier. Every WD system is a little different but what it comes down to typically is measuring…

view full answer...

Answer 5

Yes, the best option we can offer you to add fuel capacity is with the DeeZee Truck Bed Auxiliary Tank part #DZ91752X which should fit in the space you have between the cab and 5th wheel hitch no problem as it is only 9" deep. I don't have…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

I got some information from Yakima and included a diagram of the EXO SwingBase #Y34VR, which is the base part for the EXO SwingBase 2 Tier #Y82VR. Though the measurement from the pin hole to the closest edge of the carrier is not included in said…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

I reached out to Mad Ramps about the MAD-MOUNT Wall Mount Brackets for Mad-Ramps Pivoting ATV/UTV Ramps part #MR27DR and they informed me that the brackets are both 36" long x 2-1/2" tall. I have attached a photo below with this as well.

view full answer...

Answer 10

Mad-Ramps states that the part #MR54FR is best suited for ATVs/UTVs with one row of seats but if the width of your golf cart is less than 60 inches and the wheel base is less than 88 inches this would work for you.

view full answer...

Answer 11

The newer Ford trucks feature what's dubiously referred to as a 'smart' trailer connector. The connector won't send any power back on the 12-volt accessory circuit (which powers the Echo) until the vehicle is turned on, the…

view full answer...

Answer 12

Sounds like you've done a great job at installing the Redarc Tow-Pro Elite #RED44FR, and that you're on the right track when it comes to installing the Hopkins Endurance Multi-Tow Plug #HM47180 on your 2019 Ford Ranger! To wrap up your…

view full answer...

What is Preferred Method For Securing Truck Tool Box to Truck Bed if J-Hooks Don't Work

Product Page this Question was Asked From

Continue Researching