What Spindle Dimensions Does the Kodiak Disc Brake Kit k2hr35d Fit

Question

Question:

what axle dimensions are compatible with your k2hr35d kit?

asked by: Philip E

1

Helpful Expert Reply:

The Kodiak disc brake kit part # k2hr35d that you referenced is compatible with the 84 spindle which has a dimensions of 1.06 for the bearing surface closest to the threads, 1.38 inches for the other bearing surface and then for the grease seal it measures 1.73 inches.

expert reply by: Jameson C

1

click to enlarge

Answer 1

For a completely stainless steel version of the Kodiak Disc Brake Kit part #K2HR35D you will want to use the Kodiak Disc Brake Kit part #K2R35S. You will also need an idler hub like the Kodiak Trailer Hub part #KH84545S as the stainless steel version…

view full answer...

Answer 2

Brake lines don't have to be difficult to run. I recommend the Kodiak Hydraulic Brake Line Kit - Single Axle - 18' #18SI-BLKIT. This will give you one 18 foot flexible line and one 7 foot line and one 1-1/2 foot long line along with the tee…

view full answer...

Answer 3

Parts #K2HR35D and #K2R35D accomplish the same thing and have the same ratings but they fit differently applications. If you take a look at the pictures I've attached, part #K2HR35D is a complete kit with hubs and rotors where part #K2R35D does…

view full answer...

Answer 4

It sounds like you have a Demco Actuator to me like #DM8104002. We also have one with a 4 inch drop #DM8104311. Both are Hydraulic Brake Actuators that are rated at 12,500lbs.,has a 2-5/16 inch ball, and bear the DA10 model number. I was able to look…

view full answer...

Answer 5

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 8

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 9

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 10

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 11

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 12

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

What Spindle Dimensions Does the Kodiak Disc Brake Kit k2hr35d Fit

Product Page this Question was Asked From

Continue Researching