Edge Evolution Programmer for a 2014 Ford F-150 with 5.0 Liter Motor

Question

Question:

Hello I have a 2014 Ford F150 with a 5.0L. was just wondering if this product will work for my truck? Thank you

asked by: Pat

0

Expert Reply:

The Edge Evolution programmer # EP85150 will fit your 2014 Ford F-150 with the 5.0 liter motor. You can also get a custom dash pod for it using # EP18552. I have also included a link to our help article on programmers for you.

expert reply by: Michael H

0

Answer 1

For your 2013 Ford F-150 with the 5.0 liter motor I recommend the Superchips Flashpaq #SU1845 (or #SU4845 for a California approved model). The Flashpaq works well with vehicles that have additional enhancements such as cold air intake. If you want…

view full answer...

Answer 2

I checked with Edge and the CS2 part #EP85350 that you referenced has three levels for your 2018 Ford F-150 with a 5.0 liter V8. 87 octane tune adds 24 HP & 25 LB-FT of Torque Tow tune adds 30 HP & 31 LB-FT of Torque Extreme tune adds 49 HP…

view full answer...

Answer 3

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 4

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 8

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 9

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 10

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 11

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 12

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Edge Evolution Programmer for a 2014 Ford F-150 with 5.0 Liter Motor

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching