Replacement Shims for TracRac Sliding Ladder Racks

Question

Question:

Does this kit include the two plastic shims/wedges? They are included in the description but are not in the picture. They are as long as the base rails and must require a long package.

asked by: Neil

0

Expert Reply:

The long plastic shims have been replaced with smaller ones and they are now made of rubber. For a long bed truck you will need 6 of # TA8527645001. For a short bed you will need just 4 of # TA8527645001.

expert reply by: Michael H

0

Answer 1

Yes, the pocket nut in the Replacement Hardware Kit for TracRac Sliding Ladder Rack Base Rails #TAHD-21501 can be found on our site using part #TA01-2100N. This part comes in a quantity of one so you will need to place your order accordingly.

view full answer...

Answer 2

The Replacement Rubber Block for TracRac Base Rail Installation #TARB-11032-1 won't have a problem maintaining its integrity/shape as you remove and re-install the ladder rack as needed on your truck. Just make sure all your hardware is tightened…

view full answer...

Answer 3

You will need the Replacement Rubber Block for Base Rail Installation of TracRac Sliding Ladder Racks - Qty 1 #TARB-11032-1. You can get the pocket nut separately #TA01-2100N, but the bolts and other hardware are only available in the Replacement…

view full answer...

Answer 4

Replacement Pocket Nut for TracRac SR Sliding Ladder Rack Base Rails - Qty 1 #TA01-2100N has a threaded hole that is 3/8-16.

view full answer...

Answer 5

The Replacement Rubber Block for Base Rail Installation of TracRac Sliding Ladder Racks - Qty 1 #TARB-11032-1 is the correct replacement for the TracRac SR Sliding Truck Bed Ladder Rack w/ Over-the-Cab Extension #TH43002XT-782EX. This replacement…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Yes, you can replace your current Lippert Equa-Flex equalizers with the MORryde AllTrek 4000 Equalizers #MR29DR on your 2018 Highland Open Range. The yellow octagons on the front and rear are a for correcting the alignment of the axles and are not…

view full answer...

Answer 9

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 10

The Thule TracRac CapRac Ladder Rack for Camper Shell/Truck Cap #TH29200XT is not actually meant to be installed into top tracks. This crossbar system is actually meant to be installed in fixed points on your camper shell so it's not going to…

view full answer...

Answer 11

If you have the Ford 3" hitch then you can definitely add it but, yes it would change the weight capacity. The TorkLift Cannon Hitch Extension item #TLE1636 only has a 3,600 lbs towing capacity and a 360 lbs maximum tongue weight. If used with a…

view full answer...

Answer 12

The Air Lift systems that fit your 2022 Ford F-350 are single rear and dual rear wheel specific so for your dually you need the following kit: - Air Lift LoadLifter 7500 XL Ultimate Air Helper Springs #AL86KV I also recommend checking out a…

view full answer...

Replacement Shims for TracRac Sliding Ladder Racks

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching