Brake Controller Wiring Functions to Install on a 1990 Dodge D250 Pickup

Question

Question:

I have a 1990 Dodge D250 with existing seven way in the bed for fifth wheel and one also on the bumper. I bought the pigtail for my Prodigy P3 and need to connect it up to four disconnected wires. I have a white on the negative side of my battery and know where that goes. I have a red with an inline fuse, so assume that is for power. I have a blue that comes all the way from the back of the truck and connects into the plugs. I have another red that disappears under the dash near the brake pedal. Your plug has a blue brake output and a red stop, besides the two obvious connections. Can you assist me with which of those should hook up to my two wires and if not, would I ruin the Prodigy if I am wrong with my 50/50 guess and hooked up those two wires backwards?

asked by: Robert M

0

Expert Reply:

The red wire that disappears under the dash of your 1990 dodge D250 pickup is input from the brake switch and will go to the red wire on the brake controller. Blue is output to the trailer brakes and connects to the blue wire on the brake controller.

White is ground as you know and connects to the controller white wire and the fused red wire is for power which connects to the black brake controller wire. If you had switched the other red wire and the blue wire nothing would have happened so it would not have damaged the controller.

expert reply by: Michael H

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Hey Antoine, so the two kits you mentioned are actually really similar and honestly I would go with the part #ETBC7 if I were you. The #ETBC7L is basically the same thing minus a couple wires and breakers so you may as well get the kit that has…

view full answer...

Answer 9

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way is…

view full answer...

Answer 10

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Brake Controller Wiring Functions to Install on a 1990 Dodge D250 Pickup

Product Page this Question was Asked From

Continue Researching