Product Dimensions and Mounting Dimensions of Hopkins Graduated RV Levels

Question

Question:

Hello! I am a designer at Felling Trailers in Sauk Centre, MN. We are going to be using your Hopkins trailer level #HM08525 on some of our trailers. I was wondering if you had any more details on this product, particularly material specs and more dimensions. I would like to provide mounting holes on my drawings, but am unable so far to find the hole location dimensions. Any help will be much appreciated. Thanks and have a great day!

asked by: Shannon B

1

Helpful Expert Reply:

I went out to the warehouse to take some measurements of the Hopkins Graduated RV Levels, Stick-On # HM08525 for you.

I found the level to measure approximately 3-3/4 inches long x 1-1/2 inches wide. Without the height of the logo, the level is 1-3/8 inches wide. Where the level is skinnier, it is approximately 1/8 of an inch thick. With the thickness of the level, it is approximately 1/2 inch thick.

The mounting holes are 2-3/4 inches apart on center. I confirmed with my contact at Hopkins that the hole bore diameter is 5/16 inches.

My contact at Hopkins also confirmed that the level is made from a resin plastic.

I've attached a photo with the measurements of the Hopkins Graduated RV Levels for you, as well as a review video of the levels.

expert reply by: Victoria B

1

click to enlarge

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

It does appear you are going to be able to flip the axles on your 2023 Northern Spirit 2145RBX using 2 of the Dexter Trailer Springs Over-Under Conversion Kits #K71-384-00. I will warn you Kalvin this will raise the height of your camper roughly…

view full answer...

Answer 3

The B&W Continuum #BW78FR and the Reese Strait-Line #RP66083 are both great systems. The B&W Continuum is going to be easier to set up, but as far as sway control goes, I definitely have to give the edge to the Reese Strait-Line. The…

view full answer...

Answer 4

You could remove the roof to fix the staples but that would require a ton of work and can be costly, which is why Alpha said it would be overkill. You could just hammer the staples back down and just use some self leveling sealant like the Alpha…

view full answer...

Answer 5

I see what you mean about the cover being "recessed" into the front of the trailer. After looking thru a few pictures of these 2005 Trail Lite Hybrid trailers, it appears to be a fairly unique tank cover. I am sorry to say that we do not…

view full answer...

Answer 6

I have a solution for you, but the Optronics LED RV Exterior Scene Light #UCL41CB is designed to work on 12v power only, so it's not going to work on a 110v/120v feed. Unfortunately all of the lights we've got for this application are going…

view full answer...

Answer 7

Yes, you can use the B and W Continuum #BW78FR an Air Lift air bag kit #AL88375 on your 2020 Ram 1500. You would want to first decide how much air pressure in the bags you want and then setup up the Continuum and you'd be set.

view full answer...

Answer 8

Yes, I was able to verify with Curt their Front Mount Trailer Hitch Receiver #C31078 will fit your 2024 Ford F-250 4 wheel drive.

view full answer...

Answer 9

The RV Mesh Pocket part #OBE64FR that you referenced does not have a weight capacity listed or a weight that it would come off the snaps so you'd have to use your best judgment. Most common things you'd put in a pocket like this wouldn't…

view full answer...

Product Dimensions and Mounting Dimensions of Hopkins Graduated RV Levels

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching