Locking Hitch Pin for Prorack 4 Bike Rack PR8062404

Question

Question:

Hi, Is there any way to lock the threaded hitch pin?

asked by: AJ

0

Expert Reply:

There certainly is a way to lock the hitch pin of your Prorack PR8062404 4 bike rack. For the hitch lock only, use part # Y07235 or if you wanted the hitch lock plus a cable lock to secure the bikes to the rack, use part # Y07238.

If you click on the two links, you can see product demonstration videos for the hitch lock and the cable/hitch lock combo.

expert reply by: Mike L

0

Answer 1

There is a way to key a Yakima HitchLock, part #Y07235, the same way as your Yakima Yakima Holdup 2 Bike Hitch Mounted Folding Rack, part #Y02443. What you will need to do is find the lock number that should be stamped on the front of the lock…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

Just looking at your Tern HSD bike with fenders, I'm going to say no the Saris MHS Bike Rack for 1 Bike #SAR23MR is not going to work. I did some research and it looks like a lot of Tern owner's went with the Hollywood Racks Sport Rider SE…

view full answer...

Answer 7

The best e-bike capable bike rack for your 2024 Subaru Crosstrek is the Hollywood Racks Destination E Bike Rack item #HLY66ZR. This bike rack has a 70 lbs per bike capacity and works with fat tires up to 4-1/2" wide. It has padded clamps that…

view full answer...

Answer 8

Yakima has a few different anti-rattle threaded hitch bolt designs and the one you want for your Yakima EXO SwingBase Swing Away Hitch Extender #Y34VR is part #Y52FR on our site. This is the same as the 8880953 you mentioned, it just has our part…

view full answer...

Answer 9

Yes, it would! The Trailer Light Mounting Bracket item #BK70BB and the LED Light Kit item #98174LED would still be the best way to add a set of lights to a Yakima OnRamp Bike Rack 1-1/4" item #Y96FR. I have attached a picture below that a…

view full answer...

Answer 10

The Yakima LockUp Hitch Lock and Cable Lock Item #Y07238 appear to be the same as its counterpart on the Yakima site SKU: #8007238. In regards to a red piece at the end of the lock the Yakima DeadLock Hitch Lock and Integrated Locking Cable has been…

view full answer...

Answer 11

Since the lock number of your hitch lock is only listed on the side of the lock core, and yours is locked and therefore not accessible, the only solution is to replace what you have with a new hitch bolt and lock. For that you'd need part…

view full answer...

Answer 12

I got some information from Yakima and included a diagram of the EXO SwingBase #Y34VR, which is the base part for the EXO SwingBase 2 Tier #Y82VR. Though the measurement from the pin hole to the closest edge of the carrier is not included in said…

view full answer...

Locking Hitch Pin for Prorack 4 Bike Rack PR8062404

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching