Dimensions of Polar # PLR1902 Steel Trailer Ramp Spring

Question

Question:

I am looking at your ramp hinge. What size is it?

asked by: Larry

1

Helpful Expert Reply:

The entire hinge is 8-3/16 inches long by 1 inch in diameter. If you take a look at the photo I've edited for you, you can see all the dimensions of the Polar Steel Ramp Hinge, part # PLR1902.

expert reply by: Mike L

1

click to enlarge

Answer 1

The Ramp Door Hinge #PLR1902 does require welding of both portions. The tab gets welded as you stated to one side and the outside cylinders get welded to the opposite side. I've attached a couple pictures to assist.

view full answer...

Answer 2

The ramp hinges part #PLR1902 don't have a specific weight rating, but I can tell you that by the sheer size of these things and their steel constructions that three of them would be just fine for a 4,000 lb rated ramp.

view full answer...

Answer 3

It sounds like you're looking for a hinge like the Ramp Door Hinge #PLR1902. This heavy-duty hinge replaces a damaged hinge on your trailer's ramp or access door. It has a steel construction and grease zerk fitting to easily grease it for…

view full answer...

Answer 4

Appreciate the photo, and while I couldn't find any reference to part number I550-000, we do have a possible option for the ramp door hinge: - Ramp Door Hinge #PLR1902 The #PLR1902 has a pin that measures 8-3/16" long x 1" diameter and…

view full answer...

Answer 5

The Ramp Door Hinge #PLR1902 that you referenced does not come with 2 of the plates for welding. You will weld the plate to one surface and the outside ends of the pin to the other for installation. For a hinge that has 2 of the plates you would want…

view full answer...

Answer 6

Yes, the hinge part #PLR1902 will work well for you. If you used 6 of these on a fold-out style stage it would have the capacity needed and would operate well for you.

view full answer...

Answer 7

The Polar Ramp Door Hinge #PLR1902 referenced in your question has a 1/2 inch internal pin diameter. As you mentioned, the outer diameter of the hinge is 1 inch. The steel hinge also features a grease fitting to allow for a long life and smooth…

view full answer...

Answer 8

According to our friends at Redneck Trailer Supply, the reel on the end of the Enclosed Trailer Ramp Spring, #ERS120D81 measures 5 inches in diameter, so you would need a bit more than 5 inches of room on the header above the rear door of your…

view full answer...

Answer 9

If your trailer is brand new and recently purchased ideally you would return to the dealer to have the ramp corrected. The amount of misalignment you describe seems excessive for a brand new trailer. If the trailer is parked on uneven ground the ramp…

view full answer...

Answer 10

For a set of ramp hinges with a grease fitting the part #PLR1902 would work well for you. Overall the hinge measures 8-3/16 inches long, the end pieces are 1 inch in diameter, and the plate portion measures 4 inches wide by 2-5/8 inches deep. I…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Dimensions of Polar # PLR1902 Steel Trailer Ramp Spring

Product Page this Question was Asked From

Continue Researching