Does It Matter Which Way the Valve Stems Face on Wheel When Installing Wheelmaster Inflation Kit
Question:
My dually rear wheels on my 2008 Dodge now have both inner and outer valves lined up together. Should I remount the outer wheel, so that valves would be positioned opposing each other, so that mounting clips would be on opposite sides of the hub cover?
asked by: Allan
Expert Reply:
To install the Wheel Masters Airless 4-Hose Inflation Kit # WM8001 it would be easier to route the lines if the valve stems were both installed on the outsides of the rims. So that the valve stems are facing to the outside of the truck. Otherwise you would need to route the one line through it's rim and through the other rim as well.
You can try it as-is if you do not want to mess with removing the wheels, but you may not have enough line depending on the wheel setup.
Product Page this Question was Asked From
Wheel Masters 4-Hose Inflation Kit - 16" to 19-1/2" Dually - Hub Mount
- Tire Inflator
- Inflation Kit
- 16 - 19-1/2 Inch Dual Tires
- Hub Mount
- Wheel Masters
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Trailer Hitch
- Video: etrailer Trailer Hitch Receiver Installation - 2023 Subaru Crosstrek
- Video: Wheel Masters 4 Hose Inflation Kit Installation
- Shop: Wheel Masters 4-Hose Inflation Kit - 16" to 19-1/2" Dually - Hub Mount
- Shop: Wheel Masters 4-Hose Inflation Kit - 16" to 19-1/2" Dually - Hub Mount - 135-Degree Bend
- Q&A: Are Schrader Valves Removed When Installing Wheel Masters 4-Hose Inflation Kit 8001
- Shop: Hook Probe Circuit Tester
- Video: Roadmaster EZ5 Base Plate Kit Installation - 2018 Chevrolet Equinox
- Video: MB Sturgis Propane - Tees - 103606 Review
- Video: Wheel Masters Tire Inflation and Repair - Tire Inflation - WM8004 Review
- Video: Wheel Masters 4-Hose Inflation Kit Installation - 2020 Jayco Redhawk Motorhome
- Video: Wheel Masters 4-Hose Inflation Kit Review
- Shop: Bulldog Winch Double Cylinder On-Board Air Compressor - 200 psi - 4.2 cfm Maximum Air Flow
- Shop: Wheel Masters 2-Hose Inflation Kit - 16" to 19-1/2" Inner Dually - Hand Hole Mount
- Shop: TireMinder 4-Hose Inflation Kit - 16" to 19.5" Dually - Tire Rim Mount
- Search Results: tire valve extension
- Q&A: Would Only Outside Wheel of Wheel Masters Inflation Kit WM8001 Installed Cause Out of Balance
- Q&A: Wheelmaster Tire Inflation Kit for 2014 Mercedes Sprinter
- Q&A: Can Wheel Masters Airless Inflation Kits Be Installed If Wheel Has Tire Pressure Monitoring System
- Shop: Trailer Wiring
- Q&A: 7-Way RV Trailer Connector Wiring Diagram
- Q&A: 7-Way Diagram for 7-Way of 2014 Mercedes Sprinter 3500
- Q&A: Valve Stem Recommendation for Trailer Tire with Unknown Valve Stem Hole Diameter
- Search Results: trailer hitch
- Article: How to Choose the Right Trailer Hitch Class
- Search Results: hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: My Trailer Hitch Doesn't Fit
- Shop: Brake Controller
on Tire Inflator
