Recommended Thule Square Crossbar Roof Rack For 2015 Jeep Grand Cherokee

Question

Question:

question 144953 I have the sames rails as in the picture in the link above on a new 2015 Jeep Grand Cherokee. I want a Thule square bar system to mount to these rails. I am very confused as to what I need. I do not want to go to the window frame. I know Rhino makes one to mount directly to my rails but does Thule? Thanks,

asked by: Peter K

0

Expert Reply:

If your side rails on your 2015 Grand Cherokee look like the rails in the attached photo, The Thule SquareBar roof rack will work for you.

The roof rack has square crossbars and uses feet that clamp to the door jamb of your Jeep. for this roof rack you will need part # TH712500, part # TH480R, and part # THKIT1656.

All of the roof racks for the Grand Cherokees that have the all black strips on the roof, like the Altitude models, require the clips around the door jambs. The Rhino-Rack systems for your Jeep install the same way.

expert reply by: Jeffrey L

0

click to enlarge

Answer 1

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 2

Yakima's Skyline towers part #Y53TR can fit the tracks of the Retrax XR that you have with the landing pad 1 part #Y00221 but there isn't a way with the Baseline towers. Your Yakima Corebar or Jetstream bars will work with the Skyline towers…

view full answer...

Answer 3

According to Rhino Rack, if you were to go with the shorter bars, you'll only have 1-1/4 inch of leeway on each side which isn't enough in their opinion. I'd recommend going with the 71 inch bars so you'll be certain of a good fit. As…

view full answer...

Answer 4

For your setup I recommend the TrackTowers for Yakima Crossbars and Platforms - Track Mount #Y52AV which includes everything you need to mount Yakima crossbars to your Retrax cover (unless you plan on using the Round or HD bars - then you'll need…

view full answer...

Answer 5

I have a Yakima crossbar setup that is compatible with the Retrax Pro XR Tonneau Cover on your 2021 Toyota Tacoma, however, the Yakima Bedrock is not compatible and the 60" crossbars would be too short anyways. I recommend going with the…

view full answer...

Answer 6

You wouldn't want to try and move a trailer up an incline with the MT70881. The dolly itself would be fine but you would most likely not be able to pull that heavy of a trailer up an incline. And then if you somehow did get it going up the…

view full answer...

Answer 7

Trailer Valet XL Trailer Dolly #TVXL25 will be able to move your trailer at the near 90 degree angle and up the incline of the driveway. The dolly has 2 gears and you will likely find that the low speed, 27 to 1 ratio will make it easier on you…

view full answer...

Answer 8

Hey Frank, so the Blue Ox SwayPro weight distribution system you'd want is the part #BXW0750 which has a tongue weight range that matches what a 6,000 lb trailer would have.

view full answer...

Answer 9

I checked the manual and also reached out to Blue Ox to confirm this but found no notes and Blue Ox stated that the Blue Ox Base Plate Kit #BX1739 would be a compatible fit for your 2020 GMC Sierra 3500 (diesel). If you haven't picked out the…

view full answer...

Answer 10

So you can use the Trailer Valet RVR9 Remote-Controlled Trailer Dolly #TVRVR9 you were looking at, at a maximum of 5 degrees of incline, but since your trailer is about a thousand pounds heavier than what the dolly can handle you won't be able to…

view full answer...

Answer 11

Hey Antoine, so the two kits you mentioned are actually really similar and honestly I would go with the part #ETBC7 if I were you. The #ETBC7L is basically the same thing minus a couple wires and breakers so you may as well get the kit that has…

view full answer...