Hitch Fitment of 2016 Rubicon Hard Rock Unlimited

Question

Question:

The four pre-drilled holes in the frame that you refer to have bolts going through them to what looks like the bumper. Will this hitch still fit?

asked by: John

0

Expert Reply:

As long as you can remove the bolts from your bumper beam and the space between the bumper and bumper beam is larger than 1/4 of an inch, then the # 13432 Curt hitch will work for you. The upright of the hitch will take the place of the spacer between the two.

expert reply by: Jackie C

0

click to enlarge

Answer 1

My Curt representative tells me that according to the information they have, the #13432 will fit your Hard Rock 2016 Jeep Wrangler Rubicon. This fit to the frame and not the bumper so it will not interfere. Since you already have the wiring harness,…

view full answer...

Answer 2

We have an aluminum 7 spoke 14 inch trailer wheel that looks pretty close to the wheel in the picture you sent us, but it's not an exact match. For that wheel you would want the part #AM22329. For a 205/75R14 you can use #AM10234 or tire #AM10229…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 10

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Hitch Fitment of 2016 Rubicon Hard Rock Unlimited

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching