Latch Pins Needed to Hold Trunnion Bars in the Weight Distribution Head

Question

Question:

I have lost the pin that holds the Trunnion bar in Place where can I order them Thanks

asked by: Hugh M

0

Expert Reply:

If you have an older style Trunnion weight distribution head then the Replacement Trunnion Latch Pins for Reese Standard Trunnion Style Weight Distribution, item # 58025, is the correct item.

Newer style weight distribution with trunnion bars do not use latch pins, they use a twist lock design where the trunnion bar is inserted from the side and twisted to the towing and hookup position.

If you need the pins that secure the tip up brackets on your weight distribution system you will need the Reese Replacement Clips for Weight Distribution Uplift Brackets (Qty 2), item # 58029.

expert reply by: Robert G

0

Answer 1

The part number 125340 you referenced is actually a motor, and the correct replacement for that is Replacement Motor #LG-142178. However, since you mentioned gears in the gearbox, you will need to replace the entire thing, which for your landing…

view full answer...

Answer 2

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…

view full answer...

Answer 3

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to…

view full answer...

Answer 4

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 5

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 6

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 7

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 8

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 9

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 10

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 11

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 12

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Latch Pins Needed to Hold Trunnion Bars in the Weight Distribution Head

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching