Where is the Cartridge Location for Installing a Katt's Block Heater in a 2012 Toyota Camry

Question

Question:

Hi, I just received the engine block heater cartridge style for my 2012 Toyota Camry. I cannot locate the hole that this cartridge fits into, any clues as to where to locate it?

asked by: Don M

0

Expert Reply:

The cartridge location for installing the Katt's Heater part # KH11813 in your 2012 Toyota Camry is rear left if you have the 2.5 liter or the front left if you have the 3.5 liter.

I attached a picture that shows where this will be located on your engine.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Yes, we do have a hitch receiver for your 2022 Toyota Highlander XSE. It is the Curt Trailer Hitch Receiver item #C99FR. This receiver is a confirmed fit for your XSE model Highlander. It has a maximum gross trailer weight of 5,000 lbs and a maximum…

view full answer...

Answer 2

I really wish we had the chance to install the Kat's heater #KH13150 so we could provide an install video or pictures but the best is the following written instructions: To install the heater you will first need to drain the cooling system. Then…

view full answer...

Answer 3

The Kat's Heaters Thermostatically Controlled Circulating Tank Heater #KH30115 basically just installs in the lower radiator hose and plugs in when needed. After that you'd just need to plug the heater in and you'd be set. To install the…

view full answer...

Answer 4

The Kat's Heaters Lower Radiator Hose Heater w/ 270 F Thermostat - 1" Hose - 400W #KH16400 is a universal fit, so it may require slight adaptation for each fit. From what I can find online, it appears the CR-V models use a hose that is…

view full answer...

Answer 5

I understand your confusion as the installation manual for the Kat's Heaters Custom Fit Engine Block Heater part #KH11812 on your 2012 Hyundai Tucson with the 2.4L I4 engine are bit hard to understand. I will certainly do my best to help guide…

view full answer...

Answer 6

I have a block heater solution that is a fit for your 2008 Mitusubishi Lancer but the part #KH13150 is not it. Instead you would want the part #KH11812 which is a confirmed fit and would work well.

view full answer...

Answer 7

The correct fit for your 2009 Lexus RX 350 is the Kat's Heaters Custom Fit Engine Block Heater - Cartridge Style - 120V - 400 Watts #KH11813. The correct installation location in your engine is the "LF" position.

view full answer...

Answer 8

Kat's does recommend coating the cartridge with NSCG silicone grease G-624 before inserting the cartridge heaters like the #KH11813 into the block.

view full answer...

Answer 9

For your 2011 Toyota Camry 2.4L, you will not need to remove the battery to install the Kat's Heaters Custom Fit Engine Block Heater - Cartridge Style - 120V - 400 Watts #KH11813. The plug will install in the rear left of your engine block.…

view full answer...

Answer 10

Yes, the Kat's Heaters Custom Fit Engine Block Heater #KH11813 that you referenced is confirmed to fit your 2016 Toyota Camry Hybrid model with the 2.5L engine. It will install on on the rear left side of the engine block (at the back corner of…

view full answer...

Answer 11

The Kat's heater part #KH11813 is a fit for your 2014 Toyota Camry with a 2.5 liter 4 cylinder engine. Kat's says to use the cartridge that is behind the passenger side of the engine block as you are facing the engine with the hood popped.

view full answer...

Answer 12

As long as you have found the correct hole in your 2015 Toyota Tacoma the Kat's heater part #KH11813 would be correct for it and should slide right in. Since the hole is somewhat difficult to access you are most likely not angling it in…

view full answer...

Where is the Cartridge Location for Installing a Katt's Block Heater in a 2012 Toyota Camry

Product Page this Question was Asked From

Continue Researching