Replacement Glo-Brite 118R Lens Recommendation

Question

Question:

Do you carry a replacement lens red made by Glo Brite? P?N 11 8A/117 R. Thank you

asked by: Duane W

0

Expert Reply:

Based on my research, the Glo-Brite 118R red light is approximately 4 inches long by 1-1/2 inches wide. I spoke with my contact at Optronicc who confirmed that their Replacement red Lens # A44RB will fit the Glo-Brite 118R trailer light.

expert reply by: Jameson C

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 4

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 5

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Assuming your tires are in good shape without any bulges the easiest way to determine if you have a bent spindle is to take a straight edge that is longer than the tire and lay it across the tire parallel with your trailer frame and then measure the…

view full answer...

Answer 12

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Replacement Glo-Brite 118R Lens Recommendation

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching