What Is Stud Length On Dexter Trailer Hub and Drum Assembly # 84556UC3

Question

Question:

What is the stud length for these hubs? Im going to run a 5x150 adapter on top of them for a CDN M101 trailer to convert to Land Cruiser bolt pattern. I want the studs to be below the face of the adapter.

asked by: Dennis

0

Expert Reply:

I went to our warehouse and measured the studs on the Dexter Trailer Hub and Drum Assembly, part # 84556UC3 for you.

The stud is 1-1/4 inches long on the hub. I have attached a photo of the hub with the measurement you can check out.

expert reply by: Jeffrey L

0

click to enlarge

Answer 1

Since you have a brake mounting flange on your boat trailer you could pretty easily install brakes on the trailer. Most likely the mounting flange is a 4 bolt flange (all 4 bolt flanges are the same), since your trailer is most likely not too heavy…

view full answer...

Answer 2

In some situations, brakes can be installed on only one axle of a tandem axle trailer, however you should first check your state laws to see how many brakes are required for the gross vehicle weight rating (GVWR) of your tandem axle trailer. Some…

view full answer...

Answer 3

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 4

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 5

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 6

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 7

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 10

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 11

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

What Is Stud Length On Dexter Trailer Hub and Drum Assembly # 84556UC3

Product Page this Question was Asked From

Continue Researching