Which Line is Return Line on Ford C4 Transmission for Installing Transmission Cooler

Question

Question:

without being able to start the engine,, which port on the c4 transmission does the upper transmission cooling line on the radiator attach to on the transmission,,, . The one closest to the front OR the closest to the rear. thank you ,,,

asked by: Gerry

0

Expert Reply:

The rear line is the return line on a C4 transmission like what you have in your 1983 Ford Mustang. This would the line that you would install the transmission cooler on.

expert reply by: Jameson C

0

Answer 1

For cooling two different systems, using a combination cooler would be a good way to go because it saves some space in the engine compartment and you only have to mount one cooler. You could use a kit like #D15902. You would not use the oil filter…

view full answer...

Answer 2

Only the return line gets disconnected from the factory cooler when installing a transmission cooler like the Derale Transmission Cooler part #D13502. Basically you remove the return line for the factory cooler, connect the inlet or the…

view full answer...

Answer 3

When comparing the Flex-a-lite Transmission Cooler #FLX400117 to the similar Derale Series 8000 Transmission Cooler #D13502, there are very few differences between them. Both have an aluminum construction, include all hardware needed, and are…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 7

You do have the option to utilize the air brakes on your 2023 Freightliner Cascadia to control electric trailer brakes using the Hayes Air Actuated Trailer Brake Controller, part #HA100400C. However, we mostly recommend just using an electric brake…

view full answer...

Answer 8

Hey Antoine, so the two kits you mentioned are actually really similar and honestly I would go with the part #ETBC7 if I were you. The #ETBC7L is basically the same thing minus a couple wires and breakers so you may as well get the kit that has…

view full answer...

Answer 9

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Answer 10

A factory 7-way trailer connector isn't all you need to power a trailer's electric brakes. You still need a brake controller. Some Ford F-150s are equipped with a factory integrated brake controller, which you may have. If your 2012 Ford…

view full answer...

Answer 11

The best brake controller for your 2024 Toyota Grand Highlander is from Redarc, and the correct part number for it and the needed wiring adapter is the following: - Redarc Tow-Pro Liberty Trailer Brake Controller #RED24FR - Wiring Adapter for Tow-Pro…

view full answer...

Answer 12

For your 2024 Hyunda Santa Cruz we have the Curt 7-way kit part #C68JR that is a confirmed fit. This installs by plugging into a factory wiring connector on your vehicle which means a really easy install that doesn't require any splicing.

view full answer...