Front Hitch Recommendation for a 2015 Chevy Silverado 3500

Question

Question:

I have a Chevrolet 2015 Silverado 3500HD model, will this front hitch fit this specific model?

asked by: Ernest D

0

Expert Reply:

Yes, the Draw Tite hitch part # 65078 that you referenced has been confirmed as a fit for your 2015 Chevy Silverado 3500 so I would recommend it for you.

expert reply by: Jameson C

0

Answer 1

For a similar front hitch that I can show you how far it will stick out in font of your bumper, which will let you see how easily it would be to pin, check out the Curt Front Hitch part #C31023. I attached a couple pics as well to show you what it…

view full answer...

Answer 2

If you were to use a 14" hitch extender like theCurt Hitch Extender for 2" Trailer Hitches - 14" Long #C45795 with a front mount trailer hitch like the Draw-Tite Front Mount Trailer Hitch Receiver part #65078 then your new vertical…

view full answer...

Answer 3

Glad to hear that you will be using the Draw-Tite #65078 to mount the (discontinued) Superwinch Tiger Shark Off-Road Winch SW1595200 to the front of your 2019 Chevrolet Silverado 3500. To easily swap the Tiger Shark winch from the front of your…

view full answer...

Answer 4

The tow hooks on your 2015 Chevrolet Silverado 3500 do not need to be removed to install the Draw-Tite Front Mount Trailer Hitch Receiver part #65078. The bolts that hold the tow hooks do get removed but only to set the trailer hitch in place as they…

view full answer...

Answer 5

The front ends of the Silverados and Sierras like your 2018 GMC 2500 are a bit different but the fascia trimming required is the same as you can see in the two attached pictures when installing front hitch #65078. Basically a hole gets cut through…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...