Recommended Lug Nuts For 2002 Yacht Club M20 Motorcycle Trailer

Question

Question:

I need to replace my old rusted lug nuts on my 2002 YachtClub MC 20 motorcycle trailer. What size do I need?

asked by: Brian B

0

Expert Reply:

The lug nuts you need for your Yacht club M20 motorcycle trailer are 1/2 inch fine thread. My contact told me that the wheel bolt pattern is a 5 on 4-1/2 inch if you ever need to replace the wheels on the trailer.

The lug nut I recommend for your trailer are part # CE11051. I have attached a link to a product review video you can check out.

expert reply by: Jeffrey L

0

Answer 1

Yes, your BFGoodrich Mud Terrain T/A KM 255/75-17 Tire will fit inside theThule Roof Cargo Basket part #TH859XT on your 2014 Jeep Grand Cherokee Limited. The tire has an overall diameter of 32.1" and the internal dimensions of the basket…

view full answer...

Answer 2

Using the gasket product is not really necessary, as the 10-36 double lip seal will do a good job of keeping the grease in its place unless the hub is being overfilled with grease. If you are dealing with a idler hub with no brake assembly or brake…

view full answer...

Answer 3

We do not carry a tool that will help install your races, though I can pass on some information for you that might be helpful. To install your races, this is what you'll want to do, according to our help article on replacing bearings, races and…

view full answer...

Answer 4

The correct torque for installing lug nuts on your 5 X 8 trailer's 5-lug wheels will depend on the size of the lugs. For a 1/2-inch lug the torque spec ranges from 75- to 85-ft-lbs. For a 9/16-inch lug the torque spec ranges from 135- to…

view full answer...

Answer 5

An oil seal like Redline part #9103309 installs in the back side of the hub (the side nearest the trailer's frame) with the sides or "legs" of the seal inserted into the hub's bore. This means that the flat metal surface of the seal…

view full answer...

Answer 6

It is very likely that you have a 2100 or 2200 lb axle on the trailer however, the only way to know for sure is to find a tag on the axle itself. If you are not able to find the sticker on the axle we can narrow down the search with other…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Recommended Lug Nuts For 2002 Yacht Club M20 Motorcycle Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching