Is Spindle Available For Kodiak 12 Inch Hub And Rotor Assembly For 5,200 - 6,000 Lb Axles

Question

Question:

Can you provide the part numbers of the spindles that you stock that will work with the KHR12 hub?

asked by: Joe M

0

Expert Reply:

We do not offer a spindle that will work with part # KHR12D. This hub is designed to fit 5,200 - 6,000 lb axles and wheels that are 15 inches diameter or larger.

You can contact your local axle retailer and ask about a spindle that will work with this Hub. The inner bearing (sold separately), is part # 25580 and has an inner diameter of 1.750. The outer bearing (sold separately), is part # 15123 and has an inner diameter of 1.250.

The inner race (included), part # 25520 has an outer diameter of 3.265 and the outer race (included), part # 15245 has an outer diameter of 3.376.

The grease seals (sold separately), part # RG06-070, have an inner diameter of 2.250 and an outer diameter of 3.376.

expert reply by: Jeffrey L

0

Answer 1

I do have a way to help you get the correct replacement rotor hub for your 2004 Four Winns trailer, but unfortunately we do not have a list of parts on trailers. Usually we can help you get the correct replacement parts based off of the weight…

view full answer...

Answer 2

If you have a standard 6k trailer axle the Kodiak kit part #KHR12D is going to be a fit for it. Easiest way to check is to pull the hub off your current axle and check the bearing numbers in it. If they are #25580 and #15123 (which this kit does not…

view full answer...

Answer 3

I did some research and found that the 2,600 lb Hub, #22834, takes the #1779 outer bearing and #2788 inner bearing and would use the #29031 grease seal. This hub has a 6 bolt on 5-1/2 inch bolt pattern. This sounds like the hub you have, and…

view full answer...

Answer 4

The axle tube dimensions should be the same from anything between 5,200 - 7,000 lbs. I know for sure the outer diameter will be 3" as this is a standard but it would not hurt to measure the inner diameter when fittings the #42 E-Z Lube Spindle…

view full answer...

Answer 5

The Outer Bearing #1779 and Inner Bearing #2788 are going to be specific to your current 22834 hub. You will need to replace your axle as the current 5,200LB axles use a much larger spindle. We do have the following axles available that will included…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 8

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 12

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Is Spindle Available For Kodiak 12 Inch Hub And Rotor Assembly For 5,200 - 6,000 Lb Axles

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching