Inner Diameter of Inner Tube on Pro Series Square Jack with Footplate

Question

Question:

Item #PS1400800383 Can I get the inside measurement of the tube that the foot slides into please?

asked by: Jeff D

0

Expert Reply:

I went out to our warehouse to measure the inner diameter of the inner tube of the Pro Series Square Jack with Footplate # PS1400800383. I found the inner diameter to be 1.7 inches.

I have attached a photo showing this measurement for you.

expert reply by: Victoria B

0

click to enlarge

Answer 1

I have not heard of any complaints from customers about the Pro Series Trailer Jacks. The #PS1400800383 jack features a zinc plated inner tube and the jack is constructed of steel. The Pro Series #PS1400800383 is comparable to the Bulldog Square Jack…

view full answer...

Answer 2

The dimensions for the bottom plate of the Pro Series Square Jack #PS1400990376 are 8-3/4" on the handle side of the plate and 7-7/8" on other side. The outer jack cylinder is 4" square and 24-18" tall. I have included the…

view full answer...

Answer 3

The Pro Series Square Jack - Drop Leg w/ Spring Return, #PS1400950376, that you referenced would work well for your trailer, but you would most likely have to do some fabrication to install this jack on each side at the rear. The outside dimension of…

view full answer...

Answer 4

The Pro Series Square Jack, #PS1401010376, can work in tandem with another jack but it was not designed to have a mate that has a pin facing out opposite if #PS1401010376. What you can do is use #PS1400990376, which has the pin at the front. You…

view full answer...

Answer 5

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 6

What you need for your Isuzu NPR truck is a powered converter #C59236. It is compatible with incandescent and LED trailer lights. I have included a link to the installation instructions for you. This harness does require a direct connection to the…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

The 1-7/8 inch width is what is rounded up to 2 inches which is a standard width for winch straps. The 14 foot length is not something we carry. I recommend the Hand Winch Strap with Safety Hook, 2" Wide x 15' Long - 4,000 lbs #DL24239 or…

view full answer...

Answer 9

The 18.5x8.5-8 is actually an old tire size that is not used much anymore. The closest metric size to your existing tire would be 215/60-8. Your wheel most likely has a 5-on 4-1/4 inch bolt pattern (see link), you will want to make sure that the bolt…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

I can end this debate for you real fast! Trailer tires, which will have an ST in front of the size, should always be inflated to the maximum psi indicated on the tire. Trailer tires usually do not have a recommended and maximum psi indication so I am…

view full answer...

Answer 12

Below is the general process for bleeding an electric over hydraulic brake actuator like #K71-650. Fill reservoir with NEW brake fluid. Never re-use brake fluid that has been salvaged or removed from another system. Remove the key from the breakaway…

view full answer...

Inner Diameter of Inner Tube on Pro Series Square Jack with Footplate

Product Page this Question was Asked From

Continue Researching