Does Dexter 12 Inch Electric Trailer Brake Assembly # 23-181 Include the Mounting Hardware

Question

Question:

I have a 2006 pj trailer with two 7000 lb axles and one of the trailer brakes are missing the passager side when i took the brake drum wasmt there so im buying this new brake i think it looks like the correct part but im missing the 5 bolts that holds the brake assbly in place do you provide new bolts wen i buy this part or you sell it separly cuz i need em my old ones are not there no more thanks

asked by: Juan

1

Helpful Expert Reply:

The replacement right-hand brake assembly you referenced, part # 23-181 does not include the mounting hardware. You'll need 5 of the # 38N nuts and 5 of the # 7-5 bolts. Something else to be aware of, some time ago Dexter stopped including the mud and crud plugs that cover the brake adjuster holes. We offer them as part # BP10-220 for 4 plugs.

expert reply by: Mike L

1

Answer 1

You will experience some reduced braking power when using the Dexter Trailer Hub and Drum Assembly #8-393-4UC3 with 12-1/4 x 2-1/2" brake assemblies compared to the #8-285-11 with 12-1/4" x 3-3/8" brake assemblies. Between the two I…

view full answer...

Answer 2

You will have no problem using a Dexter brake assembly on a Lippert 7K axle. We have installed several Dexter brake assemblies on Lippert axles at our shop. Lippert and Dexter use the same standard mounting pattern and brake sizes. If you want…

view full answer...

Answer 3

I had our warehouse measure the distance between the inner and outer races of the Dexter Trailer Hub and Drum #8-285-11 and #8-393-6UC3-A and they found that both of them have the exact same 1-3/4" measurement, so as long as you have the #25580…

view full answer...

Answer 4

There are differences in them but we do have what you are looking for and they can in some situations be used together. The Replacement Trailer Hub Bearing you have part #02475 and Replacement Race for 02475 Bearing part #02420 are designed to work…

view full answer...

Answer 5

I added a photo which shows the location of the heating element of the Atwood Water Heater GC6AA-10E for you. It is item number 17 in the diagram. Atwood does recommend having a professional do the job if you are replacing it due to its location.

view full answer...

Answer 6

We have had a similar question to this come up and we were able to determine that the number AS-13 M-VDO449 that you listed is stamped on the vent cover part #BVD0449-A01. If you are looking for the entire fan setup and not just the cover you would…

view full answer...

Answer 7

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 8

Surge brakes use a hydraulic actuator to push fluid to the cylinder piston to activate the brake shoes on drum brakes or brake pads on disc brakes. This pressure should only be applied when weight is pushing against the hitch ball, so no pressure…

view full answer...

Answer 9

The Blue Ox systems cannot be moved back that far but we do have the perfect system for you. Take a look at the Reese SC weight distribution systems linked to the right (minus the ones that say Light Duty). These systems have narrow brackets that can…

view full answer...

Answer 10

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Does Dexter 12 Inch Electric Trailer Brake Assembly # 23-181 Include the Mounting Hardware

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching