Replacement Mounting Plate for Surco Spare Tire Bike Rack BT300

Question

Question:

Is a replacement Back Plate available for the Surco Spare Tire 3-Bike Carrier # BT300? The plate to which the main assembly piece is attached. It has a flat plate welded to a several inch long square section, and the bolt is threaded into this section. If this is available, how do I obtain it? Thanks.

asked by: Pat T

0

Expert Reply:

The replacement back plate you would need is part # SPN-115. This is the correct part number for your Surco Spare Tire Carrier part # BT300.

expert reply by: Jameson C

0

Answer 1

The Surco Spare-Tire-Mounted Cargo Basket - 19" Long x 43" Wide #SPSJ4319 has a removable mount as you mentioned. The Replacement Back Plate for Surco Spare Tire Mounted Cargo Adapter #SPN550 is the exact same part as that which comes with…

view full answer...

Answer 2

The square shank on the Replacement Backing Plate for Surco Spare Tire Bike Rack #SPN-115 is 1-1/4" x 1-1/4" and measures 3-3/4" long while the holes for the bolts have a 3/4" diameter and are spaced 2-3/4" apart evenly. The…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

Yes, you can install a Curt Trailer Hitch Receiver #C11433 on your 2019 Chevrolet Spark. This receiver is capable of supporting up to 200lbs of tongue weight. With each of the Lectric 3.0 e-bikes weighing roughly 60lbs without the battery you will…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...