Do Bearing Buddies Allow Air to Escape as they Add Grease to Hub

Question

Question:

does the red eye have a way for the air to escape ? thanks

asked by: Jerry

0

Expert Reply:

The seals on a trailer hub are not air tight. If you are adding grease with a Kodiak Red Eye or Bearing Buddy like the part # BB1980A-SS that you referenced the grease will displace the air.

expert reply by: Jameson C

0

Answer 1

I went out in the warehouse and pulled the Redline Grease Seal, part #13194. It does have the markings on the inside of the seal that say TCM 13194 TM Taiwan and the number 11. It also has the spring around the inside lip. This seal will work for…

view full answer...

Answer 2

I went out to the warehouse to measure BoatBuckle G2 Retractable, Ratcheting Transom Tie-Downs #IMF08893. The overall width at the widest point is 4-5/8 inches. The mounting hole is right in the center so from either edge to the center of the…

view full answer...

Answer 3

The replacement hub assembly will depend on the size and weight rating of the axle. We have many options for hubs for 2,000 lb axles if it is that light of a trailer. This is the smallest axle size we offer replacement hubs for. I have provided the…

view full answer...

Answer 4

Base on your information, I recommend the Taskmaster 4.80R12 Radial Trailer Tire, Item #TT48012C. It is a radial tire specially designed for trailer use that is great for highway driving. It is a good all-terrain, all weather tire that is built…

view full answer...

Answer 5

We have exactly what you need with the Easy Grease Trailer Idler Hub Assembly for 2K Axles #AKIHUB-545-2-G-EZ-2K. This has the 5 on 4-1/2" bolt pattern, uses L44649 inner and outer bearings, and a grease seal with a 1.50" inner…

view full answer...

Answer 6

There are two different bearing combinations commonly used on 2000lb trailer axles, so determine which hub assembly will be correct for your trailer you will need to confirm which bearing combination your trailer has. The easiest way to do this is…

view full answer...

Answer 7

Yes, the 1-1/16" diameter spindle is the same as the 1.063" BTR Spindle. We have the Easy Grease Trailer Idler Hub Assembly that is galvanized in a Standard #AKIHUB-545-2-G-2K or EZ Lube #AKIHUB-545-2-G-EZ-2K. You will simply need to select…

view full answer...

Answer 8

Axle capacity is just one of the things you will need to know in order to choose the correct hub, but using that alone won't ensure a fit, there are a number of things you'll need to get the right hub. Along with the capacity of the axle, you…

view full answer...

Answer 9

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 12

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Do Bearing Buddies Allow Air to Escape as they Add Grease to Hub

Product Page this Question was Asked From

Continue Researching