Can Older Trailer Hubs be Replaced with Newer Ones with 5 on 4-1/2 inch Bolt Pattern

Question

Question:

i have a trailer that was made from an old camper frame. It has what i think are called Dexter wheels, Can i convert this to a standard 4 or 5 lug wheel? Please see description of wheel similar to mine from e bay posting. Was supposed to be a link but wouldnt work.. 13 x 4.5 Dexstar 4 Bolt Camper Trailer Wheel Rim for ST 175/80R13 Tire Dexter

asked by: Charles

0

Expert Reply:

You are going to have to remove the hubs to determine what spindle you have so that you can see if we have a hub that would fit.

If you can get back to me with the dimensions of your spindle where the bearings and seals ride or the numbers that are engraved on them I can see what we have that would fit.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The Yakima Crossbar Pads part #Y07413 that you referenced is the correct size and design to fit the factory crossbars of your 2020 Subaru Outback Wagon. These are 30 inches long and fit the aero bar design of your vehicle.

view full answer...

Answer 2

Yes, we have the Thule Surf Pad - Crossbar Pad for Square and Round Bars #TH802 that will fit your Round CrossBars #Y00409.

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 5

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 6

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 7

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 8

On Dexter 12" Nev-R-Adjust Electric Brake Assembly #23-458 the shoe pad thickness is 3/16 of an inch. Dexter says that you should replace the shoes if the material gets down to 1/16 of an inch thick or less.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

I spoke to Dexter and they said there is a bit of a process for installing the spindle nut properly. 1. You will need to thread on the inner nut, rotate the hub, then tighten the nut to 100 foot pounds. 2. Loosen the nut to remove the torque, making…

view full answer...

Answer 11

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most…

view full answer...

Answer 12

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...