Thread Size and Type for Replacement Stand-Off or Insert Nut for Stromberg Carlson RV Ladder

Question

Question:

Is this item a threaded nut? If yes, what size and thread type?

asked by: Larry

0

Expert Reply:

I went out to the warehouse and pulled Replacement Stand-Off or Insert Nut # FST-9975 to measure it. The inner diameter is 0.209 inches (5.32mm). The thread depth is approximately 1/4 inch and there are 5 threads so that would be 20 threads per inch. It is a coarse thread.

expert reply by: Michael H

0

Answer 1

The Replacement Stand-Off Nut #FST-9975 can usually just be inserted into the tube using a screw driver or socket to place it in the tube. If you can't get it all the way in then using a block of wood to tap it further into place is the best…

view full answer...

Answer 2

You want to install the Replacement Standoff Nut #FST-9975 far enough that you can put the ends in place, but not so far that the screw/bolt can't reach it. There isn't an exact science to it so you'll just need to use your best…

view full answer...

Answer 3

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 4

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 5

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 6

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 7

I checked with Curt and they do show the Curt Trailer Hitch Receiver part #C13233 as a fit for a 2022 Volvo XC90 All Models which includes the Recharge.

view full answer...

Answer 8

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 9

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 10

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 11

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 12

We have a really great kit that comes with everything you'd need to convert your 2021 Vanleigh Pinecrest 335RLP from tandem 6k drum brakes to electric over hydraulic disc brakes with the HydraStar Disc Brake Kit w/ Actuator for Triple Axle…

view full answer...

Thread Size and Type for Replacement Stand-Off or Insert Nut for Stromberg Carlson RV Ladder

Product Page this Question was Asked From

Continue Researching