Pipe Mount Jack Recommendation to Attach to 2-1/2 inch Mount on Trailer
Question:
i have to replace a trailer A-Frame swing style. it is 24inch from floor to my swivel that is 2 1/2 inch dia and raielr weighs 12k lbs and estimated tong weight no more than 3/4k lbs so do you have something for me.
asked by: Gary C
Expert Reply:
The Bulldog Round, Pipe-Mount Swivel Jack - Sidewind - 15 inch Lift - 7,000 lbs, item # BD198250, has a male pipe on the jack and a female receiver that welds to the trailer. This female receiver has an inside diameter of just over 2-1/2 inches to fit on the 2-1/2 inch male pipe welded to the jack. This jack utilizes a 5/8 inch pin to secure the jack to the trailer. When fully extended it is 31 inches from where it mounts to jack to the ground.
It sounds like this jack would work well for you, but without knowing more it's hard to say for certain. If nothing else the mount for this jack could easily get welded to your trailer.
Product Page this Question was Asked From
Bulldog Round, Pipe-Mount Swivel Jack - Sidewind - 15" Lift - 7,000 lbs
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- Leveling Jacks
- Tongue Jacks
- Steel
- 6001 - 7000 lbs
- Sidewind Jack
- Swivel Jack
- 15 Inch Lift
- Pipe Mount
- Weld-On
- With Rectangle Foot
- Bulldog
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Bulldog Round, Pipe-Mount Swivel Jack - Sidewind - 15" Lift - 5,000 lbs
- Shop: Bulldog Square Swivel Jack w/ Round Pipe Mount - Sidewind - 15" Lift - 3,000 lbs
- Q&A: Trailer Jack Pipe Mount Upgrade From 3,000 lb Bulldog Swivel Jack
- Search Results: side crank jack
- Search Results: 198250
- Search Results: m1102
- Shop: Pro Series Round, Pipe-Mount Swivel Jack w/ Footplate - Sidewind - 10" Lift - 5,000 lbs
- Shop: Bulldog Replacement Pipe Mount for Swivel Jacks - 2-1/2" Female - Weld On - 5/8" Pull Pin
- Video: Bulldog Square Sidewind Swivel Jack Review
- Q&A: What Pipe-Mounted 7000-lb-Rated Jacks Work With Bulldog Weld-On Pipe Mount # BD003155
- Shop: Round, Pipe Mount Swivel Jack w/ Footplate - Weld On - Sidewind - 14-7/8" Travel - 2K
- Search Results: bd178203
- Search Results: crown jack
- Search Results: bd198250
- Shop: Square Direct Weld Jack w/ Footplate - Drop Leg - Topwind - 29" Lift - 7,000 lbs
- Shop: Bulldog Round, Pipe-Mount Swivel Jack - Topwind - 10" Lift - 7,000 lbs
- Q&A: Availability of 2-1/2 Inch Pipe-Mount Sidewind Jack with 15 Inch Lift and Drill Power Option
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Search Results: 44649
- Q&A: Recommended Replacement for Atwood Surge Brake Actuator 85778
- Shop: Trailer Wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Replacement 5 Leaf Slipper Spring for a Tandem Axle Dump Trailer with Two 6K Axles
- Video: Choosing the Right Trailer Wiring
- Shop: Fifth Wheel Hitch
- Article: Trailer Tire Sizing
- Q&A: Seal With Dimensions to Replace 171255UC
- Video: Timbren Axle-Less Trailer Suspension System Installation
- Shop: Gooseneck Hitch
on Trailer Jack
