Strap Recommendation for Dutton Lainson Boat Winch #14627

Question

Question:

I have a 2,500 pound boat. What winch strap should I order when I purchase boat winch #14627 from you?

asked by: Brian B

0

Expert Reply:

For a strap to use with the Dutton Lainson winch part # DL14627 the part # DL24249 would be an excellent option. This is a 25 foot long strap that has a 4k capacity.

I attached a review video for you to check out as well.

expert reply by: Jameson C

0

Answer 1

The bottom plate for the Dutton-Lainson Hand Winch #DL14627 is 4-3/4" wide x 5-1/2" long, while the bottom plate of the #DL14725 is slightly larger at 4-3/4" wide x 6-5/8" long. The diameter of the spools are exactly the same at…

view full answer...

Answer 2

You can indeed use a 2 inch wide winch strap like the 25 foot long #DL24249 with the Dutton-Lainson Hand Winch #DL15504 that you referenced. This particular winch can be used with either a polyester strap like this one or wire rope, so you are good…

view full answer...

Answer 3

I spoke with my contact at Fulton and he said that the Fulton Model 881 winch that you have is an older unit. He checked on his end and they do not make any parts for that winch anymore. We do carry a wide variety of hand winches for your boat…

view full answer...

Answer 4

I went out into our warehouse to grab a Dutton Lainson Winch part #DL14627 to measure the bolt hole dimensions for you. I attached a picture that has all of them listed.

view full answer...

Answer 5

I went to our warehouse and took the measurements on the Dutton-Lainson Trailer Winch #DL14627. The barrel diameter is 1-1/8 inches, the flange diameter is 6 inches, and the drum length is 2-1/2 inches. I am including a link to a FAQ page on hand…

view full answer...

Answer 6

The Replacement Winch Handle for Dutton Lainson Winch, part #DL70336 is designed to fit Dutton-Lainson winches like part #DL15502. I went to our warehouse and measured the #DL15502 shank the handle fits. The shank measures .46 X .625 inches. I have…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 11

To replace your 1,700 lb Shelby 5407B winch I recommend the Dutton-Lainson Single Speed Winch #DL14627 which is rated for 1,800 lbs. This winch features permanently lubricated bearings, high carbon steel gears, and a Zinc TUFFPLATE finish for…

view full answer...

Answer 12

The only repair kit we have for your Profile 2000 hand winch is the Winch Ratchet Repair Kit by Dutton-Lainson item #DL70475. If this isn't what you are needing you will have to replace your winch. I recommend the Dutton-Lainson Hand Winch -…

view full answer...