Ventline Garnish Trim that is 4-1/2 inches Tall

Question

Question:

Im trying to determine which garnish trim that I need for my 2000 Fleetwood Southwind Storm 30H. The roof is 4inch inches thick and the garnish that I need to replace is 4-1/2inch in height. Which garnish trim do I need?

asked by: Jerry M

0

Expert Reply:

To get a ceiling garnish that is exactly 4-1/2 inches in length you would need the part # VA0445-37 which is 5-1/8 inches tall and then trim it down to 4-1/2 inches.

expert reply by: Jameson C

0

Answer 1

Advent Air Conditioners like part #ACM135 come with a connector that pairs up directly with the standard 6-wire connector. If you have a 9-wire connector then you need the kit #ACRG15 as well. For wiring I'm attaching some photos of diagrams for…

view full answer...

Answer 2

The Advent Air RV Air Conditioner part #ACM150B doesn't come with a start capacity but you can add one easily using the Start Capacitor for Advent Air RV Air Conditioners part #ACMSCKIT. Please note, it also does not come with a distribution box…

view full answer...

Answer 3

The Furrion Chill RV Air Conditioner and Air Distribution Box w/ Built-in Thermostat part #FR76PR has a 60 db indoor sound level which can be compared to the sound of a normal conversation. The Furrion is actually about 10 db quieter than the Advent…

view full answer...

Answer 4

The Furrion Chill Replacement RV Air Conditioner for Advent Air Setup - 15,000 Btu #FR42PV will work with your current Advent set up with your existing air distribution box, so you do not need to purchase another one. You will also need to continue…

view full answer...

Answer 5

The direct replacement for your Ventline screen with model number VD0434 is #BVD0434-31 (birch white) or #BVD0434-41 (polar white). This is compatible with Ventline Ventadome roof vent models V2092, V2110, V2094 and V2119. However, if you're…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 9

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 10

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...