Can the Redline 2-Way Pop-Up Roof Vent with Garnish Be Placed Anywhere on a Trailer

Question

Question:

Is there a correct way to place the vents? I have an 18ft enclosed with no vents right now. Where should I put these vents on the trailer?

asked by: Brad M

0

Expert Reply:

There isn't a right or wrong way to place trailer vent # RV-626-062-2756. It can go on the roof, on the sides, front, or rear. Putting it on the sides, front, or rear and having it open at the bottom would help keep out rain. Ultimately it is up to you where to put it!

expert reply by: Michael H

0

Answer 1

The vent cover on the MaxxAir Mini Deluxe Trailer Roof Vent part #MA00-03801 is 4" tall, not 10" tall. I have attached a photo of this for you as well.

view full answer...

Answer 2

The MaxxAir Mini Deluxe Trailer Roof Vent part #MA00-03801 for white or part #MA00-03851 for black is a single speed fan yes. However, when the light is on the power to the fan is reduced so you will get sort of a low speed setting but it's not…

view full answer...

Answer 3

For all intents and purposes there really is no functional difference between the Replacement Exterior Pop-Up Roof Vent #9106 and the Ventilator, Pop Up 2-Way Aluminum with Screen #RV-626-062. Either would work just as well as the other with the only…

view full answer...

Answer 4

The locking storage box #M387FR mounts in the floor. As long as you have the 19" wide x 29" long x 7-1/4" deep space, it can absolutely work in a toyhauler. The box recesses into the floor and is powder coated for protection against…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hey Travis, congrats on the new 2024 Jayco Flight 284BHS! Your travel trailer looks to have a GVWR of 7,950 lbs so I recommend going with the Equal-i-zer Weight Distribution w/ 4-Point Sway Control #EQ37121ET and pairing it with the Shank…

view full answer...

Answer 9

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly 14-1/4" x 14-1/4" and have roof vents that measure 14" x 14". To pick the correct cover, you will also…

view full answer...

Answer 12

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Can the Redline 2-Way Pop-Up Roof Vent with Garnish Be Placed Anywhere on a Trailer

Product Page this Question was Asked From

Continue Researching