Will a Fastway Weight Distribution Shank Work with a Reese WD System

Question

Question:

I have a Pro Series weight distribution hitch with Reese shank 54998. I need a shank with a 4inch drop. Will the Castaway E2 shank FA92-02-4214 work with this set up?

asked by: Kevin H

0

Expert Reply:

Yes, the Fastway Weight Distribution Shank part # FA92-02-4214 that you referenced will work with Reese weight distribution heads. Most systems (including this one), use 3/4 inch holes that are 1-1/4 inches apart so they can be used on various different setups.

expert reply by: Jameson C

0

Answer 1

Yes, the Fastway e2 Weight Distribution Shank part #FA92-02-4214 that you referenced does have the standard 3/4 inch diameter holes that are 1-1/4 inches apart. This shank fits nearly all standard weight distribution heads from a variety of brands…

view full answer...

Answer 2

So if the top of your receiver is 24 inches and the bottom of your coupler is 20 inches then you are correct, you do need a 4 inch drop. To get this, you will need to use the Fastway e2 Weight Distribution Shank - 12" Long - 10-1/4" Rise,…

view full answer...

Answer 3

Eight inches from the ground to the bottom of your weight distribution shank would be fine for most situations but like you've experienced turning into inclined driveways can cause it to drag. Your trailer must sit pretty low to call for your…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 12

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...