Pig Tail Wiring with Load Resistor for Optronics LED Trailer Stop/Turn/Tail Light

Question

Question:

What pigtail do you recommend for the Optronics Trailer Lights - STL23RB? Do you need a pigtail with a resister to prevent the fast flashing?

asked by: Darren

1

Helpful Expert Reply:

For Optronics trailer light # STL23RB you can use wiring harness # ALEDRST1B. This harness comes with a load resistor built in to prevent hyper flashing. Hyper flashing is more common when putting LED lights on vehicles and not normally and issue on trailers.

expert reply by: Michael H

1

Answer 1

Yes, the Right Angle 3-Wire Pigtail for Optronics Trailer Lights - 3-Prong PL-3 Plug #A47PB is designed for the PL-3 female connector as this is the male side.

view full answer...

Answer 2

You will wire the black and red wires from the 3 wire pig tail to the two wires from your trailer, the red wire will be wired to the turn signal circuit and the black wire will wire to the tail light circuit. The third (white) wire from the pig…

view full answer...

Answer 3

Based on what you are describing it sounds like you have an insufficient ground. Make sure your ground connection is secure on a clean, bare-metal surface. This could be on the vehicle side or the trailer side so I would make sure to check ground…

view full answer...

Answer 4

Your generation of Dodge Ram has a TIPM that controls the trailer wiring circuit fuses/relays. Your best option is going to be to run 10 gauge wire like part #10-1-1 (sold by foot) from the positive post of your battery through a breaker like part…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

Answer 11

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 12

I definitely understand being a bit overwhelmed by the amount of options in front of you, however I can definitely help with differentiating the trailer hitches for your 2019 Subaru Outback Wagon along with explaining my personal recommendation,…

view full answer...

Pig Tail Wiring with Load Resistor for Optronics LED Trailer Stop/Turn/Tail Light

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching