Retracted Height Dimension of the Bulldog Jack part # BD190708

Question

Question:

The spec says the retracted length is 12 5/8inch . Where is that measured? From the bottom of the foot to where? The center of the mount ?. Bottom of the mount ? ? ?

asked by: Curt

0

Expert Reply:

The retracted bracket height dimension of the 12-5/8 inches that the Bulldog Jack part # BD190708 that you referenced has is measured from the bottom of the foot to the center of the pipe mount bracket on the side of the jack.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The Buyers Products 1/4" Zinc Plated Safety Pin w/ Lanyard #3373006875 is designed to work with a pintle hitch like the Buyers Products 30 Ton Heavy-Duty Swivel Type Pintle Hook #337BP760A where the ball of one end of the lanyard connects to the…

view full answer...

Answer 2

The main difference between the Square Direct Weld Jack part #TJD-12000SP-F2 and part #TJD-12000SP-R2 is the location of the plunger for the drop leg. The former has the plunger on the side of the crank handle and the latter has the plunger adjacent…

view full answer...

Answer 3

The Square Direct Weld Jack part #TJD-12000SP-F2 can be used in tandem. The only thing you would need to do this would be a cross shaft which would be some sort of bar that attaches the two output shafts to one another. This is assuming you want both…

view full answer...

Answer 4

If you aren't familiar with a jack like Square Direct Weld Jack #TJD-12000SP-R2 it can have a little bit of a learning curve. Here is how it works: As you probably know the jack leg retracts quickly. First make sure the jack is not supporting a…

view full answer...

Answer 5

The trailer tire and wheel combination #AM3S862 is received from the supplier already with the tire mounted on the wheel. The supplier does not balance the combination, but when the tire is installed to the wheel they will line the high (heavy) spot…

view full answer...

Answer 6

Lunette rings do come in more than one size. The linked page displays both 2-1/2-inch and 3-inch inner diameter. . Lunette ring accessory items are also shown on the other linked page. Weight capacities for lunette rings are substantial, ranging from…

view full answer...

Answer 7

Yes! The corresponding female pipe for the Replacement Pipe for etrailer and Ram Pipe Mount Swivel Jacks #TJP-OP58 is the: -Replacement Female Pipe for etrailer and Ram Pipe Mount Swivel Jacks #TJP-FP58. Additionally, both of these parts are designed…

view full answer...

Answer 8

The distance from the center of the pipe mount to the top of the Square Pipe Mount Swivel Jack w Footplate #TJDP-7000-B measures 10-1/4 inches.

view full answer...

Answer 9

For your needs I recommend Bulldog jack #BD190708. It is rated higher at 5,000 pounds but all that means is that it will be easier on the jack. It fits all of the other criteria you are looking for. The fully retracted height is 12-5/8 inches and it…

view full answer...

Answer 10

I have a solution for you but you're going to need to weld on a pipe mount. There are no jacks available that will clamp onto your frame and give you that much of a lift. The clamps won't support that much extension. For that high of a lift…

view full answer...

Answer 11

Round, Pipe Mount Swivel Jack w/ Footplate - Weld On - Topwind - 15-1/4" Travel - 7K Item #TJP-7002-B does not have a grease fitting. But there is a another option that does. Take a look at Square Pipe Mount Swivel Jack w Footplate - Drop Leg -…

view full answer...

Answer 12

The foot plate of the Jack part #PS1401480303 that you referenced can not be removed so there would be no way to rotate it 90 degrees. A better option for you may be the Bulldog Square Jack part #BD190708. The inner leg is removable. I attached a…

view full answer...

Retracted Height Dimension of the Bulldog Jack part # BD190708

Product Page this Question was Asked From

Continue Researching