Winch Recommendation for Use as a Ceiling Hoist for Car Engine

Question

Question:

used in home garage to raise and lower 80 lb. punching bag and to change out 450 lb. auto engine.

asked by: Phillip W

0

Expert Reply:

Only worm gear winches should be used for hoisting thing like car engines as they are the only ones rated or that.

For a winch the Dutton-Lainson Worm Gear Hand Winch # DL10954 would work great as it has more than enough capacity. It also can be mounted to the ceiling to allow the winch to hoist the engine easier.

expert reply by: Jameson C

0

Answer 1

Yes, you are able to use a Synthetic Rope #BDW20095 rather than the Steel Cable #DL24104 on the Dutton-Lainson Hand Winch #DL10954. The image below shows how the line needs to be routed on the drum of the winch.

view full answer...

Answer 2

We currently do not offer the extension that you could use to operate the loop drive on winch #DL10954 because there are so many possible lengths that customers could need. As for the cable attachment it is fairly easy. First, for a cable, the…

view full answer...

Answer 3

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is…

view full answer...

Answer 4

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on…

view full answer...

Answer 5

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 8

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 9

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 10

The installation instructions for this product are recommended for individuals who have experience winding torsion springs. If you have not worked with a torsion spring system before, we recommend contacting a local garage door company to install…

view full answer...

Answer 11

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 12

The Trailer Leaf Spring, 2250 lbs. 6 Leaf, item #e27SR, is sold as a replacement spring for older trailers and measures 26 inches for eye to eye, center to center. If you are replacing the springs and hangers you will need to use the same center to…

view full answer...

Winch Recommendation for Use as a Ceiling Hoist for Car Engine

Products Referenced in This Question

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching