Recommended Reese 5th Wheel Slider Base for Use with 14K Reese Hitch

Question

Question:

I have a Reese 14 k hitch and want to add a slider to it. Will the Reese 50024 or 30048 work with it

asked by: Michael L

0

Expert Reply:

You can use Reese Square Tube Slider # RP30048 or # RP50024 round tube slider to convert your fixed Reese 5th wheel hitch to a slider 5th wheel. I verified this with my contact at Reese. This slider features 6 rollers for smooth tracking and it provides 10-inches of front-to-back travel.

expert reply by: Adam R

0

Answer 1

To mount your Reese Titan 16 5th Wheel Hitch in the Ford OEM puck system you will want the Reese Elite Series Underbed Rail Adapter item #RP30156. This adapter will drop right into your Ford's pucks and provide you with a base that is compatible…

view full answer...

Answer 2

The leaf spring inside of the Reese Round Tube Slider part #RP50024 is not a replacement part offered by the manufacturer. Therefore, if this is damaged then you will have no other option but to replace the entire slider assembly. That said, if you…

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 6

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 7

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 11

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 12

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Recommended Reese 5th Wheel Slider Base for Use with 14K Reese Hitch

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching