Replacement Jack Recommendation for Replacing Shelby 5764A Jack

Question

Question:

I have a Shelby 5764A tongue jack and was wondering if you had a recommendation on a replacement

asked by: Roger H

0

Expert Reply:

Your Shelby jack that you are looking to replace has a 1,200 lb capacity.

The Fulton Jack part # FXPD15L would be a great replacement jack that has even more capacity at 1,500 lbs. I attached a review video for this jack for you to check out as well.

expert reply by: Jameson C

0

Answer 1

For your Shelby 5856A boat trailer, I recommend the Fulton Bolt-Thru Swivel Marine Jack with Dual Wheels - Sidewind - 12" Lift - 1,500 lbs #FXPD15L. This jack has zinc plating for corrosion resistance and durable poly wheels. For the single…

view full answer...

Answer 2

I can tell you exactly how to find compatible drum brake assemblies, though I took a look and could not find any type of reference to Dico 40511. To determine the brake assemblies that will fit your 2002 Escort boat trailer, you need to know your…

view full answer...

Answer 3

If you are talking about the small opening on the outside and inside of the Orifice Connector #T1209800 then those measure 0.0010" and 0.0865" respectfully. I went out to the warehouse and measured them with the digital caliper. Please note…

view full answer...

Answer 4

Since Shelby is no longer in business, and jack handles are not universal, what that means is there isn't a replacement handle available, so your only option is to get a brand new jack. Since the Shelby is a weld-on jack, the best option we have…

view full answer...

Answer 5

You are correct that the Replacement Master Cylinder Assembly for Titan Model 60 and Aero 7500 Brake Actuators - Drum #T4395100 you were looking at is the replacement master cylinder for your older 23361. I included a video of the Titan #T4395100 for…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 12

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Replacement Jack Recommendation for Replacing Shelby 5764A Jack

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching