Could the DeeZee Tailgate Assist part # DZ43203 Be Installed on Passenger Side

Question

Question:

Can this tailgate assist be installed on the right passenger side of the tailgate? All instructions and videos are referring to the left driver side. The pre-drill hole the instruction is referring to on my vehicles tailgate is on the passenger side. The drivers side has an oval shape hole. 2015 F-350, Lariat ultimate package, 6.7L, 4x4, CC with built-in step tailgate. Thanks,

asked by: Joe

1

Helpful Expert Reply:

If the hole on your tailgate happens to be on the passenger side there is no reason the DeeZee Tailgate Assist part # DZ43203 wouldn't work on that side as well. The install would then just be on the opposite side of the tailgate.

expert reply by: Jameson C

1

Answer 1

To replace the ball mount bracket portion of the DeeZee Tailgate Assist #DZ43200 you can use part #BKT43200, which infludes the torx wrench, nutsert tool, and plate. The ball mount is not available by itself. I'm not quite sure why this piece…

view full answer...

Answer 2

For your 2015 Ford F-250 Super Duty you would only need one of the Deezee Tailgate Assists, but you would want the part #DZ43203 as it is the confirmed fit and not the part #DZ43300 that you referenced.

view full answer...

Answer 3

Husky doesn't offer replacement spring bars, so you'd need to replace the system. The GVWR of your Astoria 2773rb is right at 9500 lbs, as you mentioned. Since a trailer's tongue weight is typically between 10-15% of its fully…

view full answer...

Answer 4

I believe you are asking about ordering the nutsert and replacement tool for the DeeZee Tailgate Assist #DZ43301. The only way to get that is with the #BKT43301 that you referenced.

view full answer...

Answer 5

I do have an option for you but the Stromberg Carlson 4000 Series 5th Wheel Louvered Tailgate part #VGD-10-4000 does not have a spot for the factory backup camera. Therefore you would either need to find a way to mount this yourself, go without, or…

view full answer...

Answer 6

For the Edge CS2 Evolution Diesel Tuner you will need to enter the programming menu. You will turn on your vehicle without starting it. Then use the Menu button to open the main menu and scroll down with the arrow to the Programming on the screen.…

view full answer...

Answer 7

The pin in the 1:00 position on your 7-way is fed by the auxiliary power circuit. The wire feeding that circuit runs to the engine compartment and terminates under the brake booster and master cylinder and will have a ring terminal on the end of it.…

view full answer...

Answer 8

On GM vehicles of that vintage, the 12-V pin should be hot regardless of whether the ignition is on or not. If it isn't showing voltage even with the ignition on, you're almost certainly on the right track thinking it's a blown or…

view full answer...

Answer 9

The support capacity per etrailer Camper Jack #TJ01RT-HD that you referenced is 1,000 lbs. Since your trailer would weigh up to 5,000 lbs this would not be your best option as the jacks most likely would get exceeded. I'd go with scissor jacks on…

view full answer...

Answer 10

Both the LED Trailer Mini Clearance #MCL10AKB and Uni-Lite LED Clearance #MCL11RKB will require an 11/16" hole for mounting. These both use the same Grommet #A11GB.

view full answer...

Answer 11

The DeeZee Tailgate Assist Custom Tailgate-Lowering System #DZ43301 is the kit you need for your 2023 Ram 3500. This will allow your tailgate to open slowly when going down rather than slamming down on the cables.

view full answer...

Answer 12

The wires under the hood for power to the factory 7-Way and power for a brake controller under the dash are sometimes rather hard to see. The wire for the factory 7-Way power is located under the master cylinder and is taped to the wiring harness…

view full answer...