Towing Mirror Recommendation for a 2012 Ford F-150 King Ranch

Question

Question:

I have a 2012 Ford F-150 King Ranch edition. I saw a small side note stating that this particular model would not fit chrome mirrors. Mine are chrome but are OEM. Will these fit and if not do you have a set that will. Thanks.

asked by: Todd

0

Expert Reply:

Thanks for sending us a picture of your mirrors. The K-Source Custom Towing Mirrors # KS81810 has been confirmed as a fit for the mirrors you sent us a picture of that are on your 2012 Ford F-150.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Yes, the K-Source mirror part #KS81810 that you referenced is compatible with the mirror you sent a picture of to us.

view full answer...

Answer 2

I spoke with my contact at K-Source and the Custom Towing Mirrors, #KS81810, will fit on your 2011 Ford F150 Platinum but the LED turn signals may be partially obstructed.

view full answer...

Answer 3

I have a few potential options for you, but we do not have any 1-1/4" bike racks that are rated for use with a travel trailer. Your first option would be to replace your 1-1/4" hitch with a 2" hitch. This can be done a couple of ways.…

view full answer...

Answer 4

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 5

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 8

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 11

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...