B&W Underbed Gooseneck Hitch Safety Chain U-Bolt Recommendation

Question

Question:

I am looking for the U-bolts for the BandW Companion hitch, They look like they are larger than 1/2inch bolts. What are the right u-bolts and do you have them available? Thanks,

asked by: Will

0

Expert Reply:

It sounds like you are looking for the replacement safety chain U-bolts for your B and W underbed Companion hitch setup. For that you would want the part # BW1900-2-1600 that you referenced.

These are 1/2 inch U-bolts.

expert reply by: Jameson C

0

Answer 1

For your companion hitch the replacement pivot arms are now only available with the base which for your model 3000 is #BWRVB3500. I'm not sure what u-bolts you are referring to, so I assume it is the chains and that is part #BW1900-2-1600. If…

view full answer...

Answer 2

The Buyers Products Gooseneck Safety Chain U Bolt Kit #337BRB03 has an overall length of 5-5/8 inches and a length of 4-3/4 inches that is below the top of the truck bed. The diameter is .57 inches and the on center measurement is 1-7/8 inches.

view full answer...

Answer 3

The distance between the bolt centers of the U-bolts in the Buyers Products U-Bolt #337BRB03 kit is 1-7/8 inches.

view full answer...

Answer 4

The U-bolt in the B&W Replacement Safety Chain U-Bolt Kit, #BW1900-2-1600, measures 3-1/4 inches long x 2-1/2 inches wide. The inside measurement of the U-bolt is 1-9/16 inches. The U-bolt is also 1/2 of an inch in diameter. The attached…

view full answer...

Answer 5

For your 2017 F-350 short bed, the clearance calculation is the measurement from the cab to ball center minus 1/2 the trailer width. This will give you the minimum clearance. If that number is positive the trailer will not interfere with the cab of…

view full answer...

Answer 6

The height adjustability for the Curt Q25 5th Wheel Trailer Hitch for Ram Towing Prep Package #C16049 that you have installed in the bed of your truck is 14 to 18 inches. The height you want to use is the height that allows your trailer to set as…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 11

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

B&W Underbed Gooseneck Hitch Safety Chain U-Bolt Recommendation

Product Page this Question was Asked From

Continue Researching