Which Hayes Brake Control Wiring Adapter for 2004 Toyota Sequoia

Question

Question:

This will fit a 2004 sequoia?

asked by: Jason M

0

Expert Reply:

The Custom Wiring Adapter for Hayes Brake Controllers # HA81785-HBC is the correct one to install a Hayes controller like their Engage Time Delayed Trailer Brake Controller # HA81760 in a 2004 Toyota Sequoia with factory 7-way. The linked videos will give you additional details about these two items.

expert reply by: Adam R

0

Answer 1

Sounds like your Tacoma has a factory 7 way, so, yes the adapter you will want is #HA81785-HBC. To install your Hayes electric brake controller, you need to connect the wiring of the controller to your vehicle. This adapter plugs into the 5-pin…

view full answer...

Answer 2

The Curt Wiring Adapter #C51362 is what you need to install a Curt Discovery Electric Brake Controller #C84VV in your 2005 Toyota Tundra as long as the truck has a factory 7-way trailer connector.

view full answer...

Answer 3

Brake controllers don't have an off switch and are designed to go into a sleep mode after 15 minutes or so of inactivity. It sounds like your controller is wired up correctly in your 2009 Chevy Silverado and the controller just hasn't gone to…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 7

Hey Jeremy, Typically with boat trailers the manufacturer will install hydraulic surge brakes because you don't have to worry about the water damaging wires like you would with electric brakes. That being said, if you use a heat shrink butt…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 10

There is a trailer hitch receiver as well as a 4-way wiring harness that fit your 2022 Jeep Grand Cherokee WL; that said, we don't have any way to reference a VIN so you'll need to confirm if you do have the WL, which is the new model of…

view full answer...

Answer 11

To me it makes the most sense to put a Bike Rack #HLY64FR on the flat towed vehicle rather than above the tow bars. Especially on heavy e-bikes as they are difficult to lift that high onto the rack, but also as it only makes sense to have the rack on…

view full answer...

Answer 12

There are some subtle difference between the Kuat Piston Pro Bike Rack for 2 Bikes #KU76ZR and the Kuat Piston Pro X Bike Rack for 2 Bikes #KU98VR. Overall the two racks are very similar, there are just some subtle differences/upgrades on the Piston…

view full answer...