Length of Ultra Fab Powered A-Frame Jack from Mount to Bottom of Foot Retracted

Question

Question:

How long is the jack that hangs below the trailer. Can the foot be removed and left off for lower trailers? Do you have a video of this installation? Thank you.

asked by: Beth

0

Expert Reply:

When fully retracted the Ultra Fab Jack part # UF38-944037 that you referenced has a distance of 9-1/4 inches from the mounting bracket down to the bottom of the foot. Fully extended this measurement would be 27-1/4 inches.

The foot of the jack is removable as well. I also attached an install/review video for this jack for you to check out.

expert reply by: Jameson C

0

Answer 1

When the Ultra Fab Jack part #UF38-944037 is fully retracted the overall height from top to bottom is 27-1/2 inches. I attached a picture that has several other dimensions as well. If this jack was positioned upside down it would still function. I…

view full answer...

Answer 2

For your flat bed trailer, I recommend using 12 gauge wire like #12-1-1 at the minimum, but preferably 10 gauge wire like #10-1-1. Both of these wires are sold by the foot, so you can order the exact length you are needing. If you were to use a…

view full answer...

Answer 3

The reason that 10 Gauge #10-1-1 or 12 Gauge #12-1-1 wire is recommended for 10" brake assemblies, like part #AKEBRK-35-SA, is because they pull more power than the lights on your trailer. I believe the green wire you are referring to carries…

view full answer...

Answer 4

Our etrailer Electric Jacks Electric Jack w/ Footplate #EJ-3527-BBX are made by Pacific Rim. They also manufacture the Ram Jacks right alongside the etrailer.com jacks. Ram is a well known brand of dependable jacks in the industry and many trailer…

view full answer...

Answer 5

I attached pictures that show how the switches of the Bulldog Powered Jack #BD500187 get wired.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Length of Ultra Fab Powered A-Frame Jack from Mount to Bottom of Foot Retracted

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching