Recommended Roof Rack for a 2012 BMW X3 Without Roof Rails

Question

Question:

Question My X3 has no roof rails just small ridges thwart run from the front to rear along the roof Is your product compatible with an X3 with no rail system installed at the factory? Can you provide instructions to install? How difficult would it be to install Rhinos on my X3?

asked by: Jim

1

Helpful Expert Reply:

For your 2012 BMW X3 with a naked roof, I recommend the Vortex Aero aluminum crossbars # RRVA126B-2. The vortex strips in the C-channels will reduce wind noise and the weight capacity is 165 pounds. I would take a look at your owners manual on your X3 to view the roof weight capacity before you load anything onto your roof.

The legs you will need are the 2500 series legs # RRRLKVA and custom DK clamps and pads are # DK295. Take a look at the video review I included. It will provide you step by step instructions to install the crossbars, legs and clamps.

For added security, I recommend the Rhino-Rack locking end caps for Vortex Aero Crossbars # RRVA-LEC4. This replaces the end caps and lock in place to prevent thieves from sliding any accessories out of the C-channels.

I included a informative article for you too.

expert reply by: Chris B

1

Answer 1

Yes! The 47" WingBar Evo crossbars will fit on your 2020 BMW X3. So for the complete roof rack you need the following: 47" WingBar Evo Crossbars - Black #TH711220 or Silver #TH711200 Evo Flush Rail Feet - #TH710601 Fit Kit - #TH186007 We…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Aside from a slight change in the appearance of the crossbar (the WingBar Evo has some boxed edges as opposed to the completely smooth front of the AeroBlade) the biggest differences are the rubber strip on top of the crossbar and the weight…

view full answer...

Answer 5

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 6

For a roof rack to be compatible on your 2020 Jeep Wrangler with Sky One-Touch Power Top, it can't be mounted on the top of the roof and it needs to be high enough for the folding roof to clear. What you need are tall gutter-mounted roof racks.…

view full answer...

Answer 7

Hey Mark, so the correct Blue Ox base plate kit to use with the Blue Ox Ascent tow bar part #BX4375. is the part #BLU53FR. For lighting you can use #C96JR, and not have to worry about cutting into the taillight housing as this plugs inline with the…

view full answer...

Answer 8

The Malone Universal Crossbar System #MPG201 is a more economical choice but it still does a good job. The design and quality of Thule's system is why they have such a large difference in price. Whether you go with the Thule Crossroads system…

view full answer...

Answer 9

Thanks for reaching out, Joe! I recommend using the Rhino-Rack Aero Bar Roof Rack for Camper Shells #Y02-480B which comes with 63" long tracks as well as 54" long crossbars which should give you a little bit of overhang on your canopy. Per…

view full answer...

Answer 10

Thanks for all the details! We definitely have a way to get a cargo basket and an awning installed on your 2024 Toyota Highlander, although the aftermarket roof rack systems will use a clamping system with your door jambs instead of mounting via…

view full answer...

Answer 11

The Rhino-Rack Roof Rack for Factory Tracks #Y02-490B-NT is going to be your best bet for the tracks on the ARE topper for your 2012 Toyota Tacoma. The weight capacity is 220 lbs like you mentioned, but that's going to be the highest you'll…

view full answer...

Answer 12

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Recommended Roof Rack for a 2012 BMW X3 Without Roof Rails

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching