What Type of Hitch Accessories Would the SilentACT Anti-Rattle Trailer Hitch Lock # SHP2082 Fit

Question

Question:

Any idea if this will work with the sportrack 2 carrier. I know they have their own locking Pin, but this ones seems easier t make removing the rack easier. Thanks

asked by: Frank B

0

Expert Reply:

The SilentACT Anti-Rattle Trailer Hitch Receiver Lock # SHP2082 that you referenced is designed to fit 2 inch hitch accessories with a hollow shank.

Your Sportrack bike rack uses a threaded hitch pin so it would not work for that rack.

expert reply by: Jameson C

0

Answer 1

The bottom of the receiver portion of trailer hitch #24933 for your 2017 Mazda CX-3 will be approximately 9-1/2 inches up from the ground. There are some parts of the vehicle that hang a bit lower on the vehicle itself but as far as at the end of…

view full answer...

Answer 2

The tongue weight capacity of the EcoHitch #306-X7305 for a 2015 Mazda 3 is indeed 300 lbs. After we wrote the original product description, EcoHitch did further weight capacity testing on the #306-X7305 hitch and found that it had a higher tongue…

view full answer...

Answer 3

The overall width of the Draw Tite hitch is 41 inches, the depth front to back is 21 inches and the height is 8 inches. The weight is then 37 lb. Based on the standard checked back dimensions I believe this would be too large. Weight should be fine…

view full answer...

Answer 4

We do have trailer hitches to fit your 2019 Mazda CX-3 that are similar to the part #90092 that you referenced. The available hitches for the 2019 CX-3 are the 1-1/4-inch size like #90092 but they are lighter-duty Class I hitches. There are not any…

view full answer...

Answer 5

If your 2011 Toyota RAV4 has a 2-inch hitch receiver like Curt #C13149 then the etrailer Folding Cargo Carrier #e98874 will fit the hitch and will clear the rear of the vehicle even when folded. The etrailer cargo carrier #e98874 provides 9-1/2…

view full answer...

Answer 6

We cannot recommend you exceed the 200 lb tongue weight of the hitch that fits your 2019 Mazda CX-3, the Draw-Tite Trailer Hitch Receiver #24933. It is not designed to have that much weight so there's no telling if the structure can be…

view full answer...

Answer 7

There is actually only 1 trailer hitch that fits your 2020 Mazda 3 Hatchback so it definitely cuts down on what we need to filter through. The Curt #C98BR is a Class I trailer hitch rated for 2,000 lbs towing and has a 1-1/4" receiver rated…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…

view full answer...