Availability of Replacement Lens for Magnetic Tow Lights

Question

Question:

I have magnet mount tail lights that I need to replace the lens. Number on lens DOT SAE I6S2T2 97

asked by: Tammy M

0

Expert Reply:

I compared the picture of the lights you have to the magnetic tow lights we carry and it looks like you have the Roadmaster Magnetic lights part # RM-2120.

Which I spoke to my contact at Roadmaster and he said that any replacement lens with a 4-1/4 inch overall diameter that snaps onto the light housing would work like the part # A24RB.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The only magnetic tow lights we offered with red and amber lenses were the MaxxTow Magnetic Tow Lights (Discontinued) part MT70097. Unfortunately, the lenses on this light are not replaceable therefore your only option would be to replace the entire…

view full answer...

Answer 2

While we do not carry the Kenway brand, we still may have an option for you. Take a look at the: -Replacement Red Lens for Peterson Pedestal Mount Tail Lights #338-15R. This lens has the same diameter as your Kenway, at 4-1/8", and is also red…

view full answer...

Answer 3

To remove the lens of the Heavy Duty Magnetic Tow Lights #TL21RK that you referenced would require you to use a thin slot screwdriver to pry the lens from the housing. We don't carry the bulb type but it is a 2057.

view full answer...

Answer 4

So long as you have the appropriate cut out size, you can replace your Atwood GC6AA-10E with the Furrion RV Tankless Water Heater #FR93FR. The Atwood heater measures 12-1/2" tall x 16" wide x 18" deep while the Furrion measures…

view full answer...

Answer 5

In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly 14-1/4" x 14-1/4" and have roof vents that measure 14" x 14". To pick the correct cover, you will also…

view full answer...

Answer 6

The best way to determine which replacement tail light lens you will need is to try and locate a part number on the light housing. The SAE, Society of Automotive Engineers, number is not the part number of the light, it is just a number on the lens…

view full answer...

Answer 7

Most of the time the lenses on magnetic tow lights will be able to just pop off, but not always. If there is a gap between the lens and the base, it will work. If there is no gap and the lens is sealed to the base, you will need to replace the whole…

view full answer...

Answer 8

The inside diameter on the back of the Replacement Tail Light Lens #A52RB is 4 inches. The overall outside diameter is 4-1/4 inches.

view full answer...

Answer 9

Yes, the replacement lens for the Heavy Duty Magnetic Tow Lights part #TL21RK is the Replacement Tail Light Lens part #A52RB. I called my contact at Optronics to confirm this.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...